13
In the same respect, if your heart rate is above your programmed amount of BPM’s, the incline or speed will
automatically decrease to lower your heart rate. You may at any time during the Heart Rate Program
adjust/override the speed and/or the incline by simply pressing the correct button.
There are 3 HRC programs as follow:
H-1.
On this program, the treadmill will keep your heart rate at a desired amount of “beats per minute” by automatically
adjusting the speed only.
H-2.
On this program, the treadmill will keep your heart rate at a desired amount of “beats per minute” by automatically
adjusting the incline only.
H-3.
On this program, the treadmill will keep your heart rate at a desired amount of “beats per minute” by automatically
adjusting the speed and incline.
STEP 1:
Attach the Safety key to wake display up; the treadmill then will be on start/ready status. Press MODE button, the
INCLINE window will display H-1. Press MODE button to select H-1 to H-3.
STEP 2:
After selecting the program, Press MODE button, the TIME window will bling, press SPEED+/- or INCLINE
∧
/
∨
to
set time. Press MODE button again, the DIS. window will bling, press SPEED+/- or INCLINE
∧
/
∨
to set your age. Press
MODE button again, the CAL. window will bling, press SPEED+/- or INCLINE
∧
/
∨
to set TARGET HEART RATE.
STEP 3:
After finish setting the lasting time of the program, press START/STOP button to start the program.
BODY FAT SCALE
This function is to estimate your body fat according to the basic information of you body condition.
This estimate is not exact and persons with medical conditions and/or a specific need for accurate body fat value
should not rely on the estimations provided.
STEP 1:
Press PROGRAM button repeatedly, on the “11” time pressing PROGRAM button, the TIME window will display
FAT. Press MODE button to set the relative parameters: GENDER, AGE, HEIGHT and WEIGHT.
STEP 2:
After entering BODY FAT function by pressing MODE button, the INCLINE window will display F1, the DIST
window will display 1, it represents GENDER, press SPEED +/- button to set gender from 1 - 2, 1 represents MALE,
2 represents FEMALE. Then press MODE button to go to next step.
Summary of Contents for ENERGETICS PR 40.1
