Home
/
Interstate
/
PWR 7010
/
Operation Instructions Manual

Interstate PWR 7010, Operation Instructions Manual

The Interstate PWR 7010 Operation Instructions Manual is a comprehensive user guide designed to help you operate your product efficiently and safely. This manual is available for free download at our website, ensuring easy access to the essential information you need. Get your manual today and unlock the full potential of your Interstate PWR 7010.

Share

1
2
3
4
5
6
7

Page: 5 / 7

background image

Jump Starter Pack Device Operation Instructions

ACR/QA 1829Nov

Section-B) Jump Starter Pack Device Use Continued:

Step #5) When correctly connected, the indicator light on the safety box of the Smart Clamps will

be Illuminated; and not flashing.

NOTE: If the indicator light is flashing, locate the Manual Activation Button that is located on the

side of the Smart Clamp Safety Box. (Then press and hold the Manual Activation Button for

1 to 3 seconds; and then release the Manual Activation Button. Additionally, the

Indicator light should be illuminated and not flashing).

If all previous steps are correctly connected, your device set up should look similar to this;

View of typical under hood/bonnet jump-starter device setup

Smart Clamp

Reset Button

Indicator

Light

«
...
3
4
5
6
7
»

Summary of Contents for PWR 7010








Reviews:

No comments

Related manuals for PWR 7010

Brand: Z-Wave Pages: 44

EZ Power Remote

Brand: Pogo Pages: 1

COM-IDS(RS)-BM1-EN

Brand: idatastart Pages: 16

Brand: Quicksilver Pages: 14

Brand: Gsertel Pages: 9

Brand: OzCharge Pages: 8

Brand: Xpresense Pages: 23

Brand: Xantrex Pages: 68

Brand: SYNCRO Pages: 14

Brand: YOUNGSHIN Electronic Pages: 7

Brand: marklin Pages: 40

Brand: Carrier Pages: 44

Brand: Moree Pages: 2

Brand: Extron electronics Pages: 1

Brand: Xtream Pages: 2

Brand: Nordic Start Pages: 7

OEM-IDS(RS)-BM1-[ADS-BM1]-EN

Brand: idatastart Pages: 18

Brand: idatastart Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands