background image

www.intertec.info

Operating Instructions CP VARITHERM DBPA

HOM146742411Ien-6

Page 5 / 8

INTERTEC-Hess GmbH · Raffineriestr. 8 · 93333 Neustadt/Donau · Germany · 

 +49 9445 9532-0 ·   info@intertec.info

Profile type "P" Height x

Width x Depth

213 x 220 x 80 

mm

Profile type "P" Height x

Width x Depth

213 x 220 x 60

mm

Profile type "P" Height x

Width x Depth

213 x 220 x 40

mm

 INFO

You will find the precise technical data for your
instrument on the label.

Rated output

Rated voltage/Operating voltage

Thermostat

Temperature class

Illustration 1: 

Example: CP VARITHERM DBPA 300 T3 60

TS10 label

8

Installation

NOTICE

Carefully remove

When removing from the packaging and during
transport, the connection line must not be stressed or
bent.

For free convection, the heater needs to be installed with
ribs  standing  vertically.  The  minimum  distances  to  the
floor and to devices above it must be complied with. The
label needs to remain legible.

If  an  additional  TAE  thermostat  is  switched  in  series,
then  it  can  be  attached  to  the  surface  of  the  heater
(thermal coupling). The minimum distance also needs to
be adhered to here. Refer to the following drawing.

To  ensure  operational  safety,  the  heater  must  operate
under temperature conditions which will NOT exceed the
trigger temperature of the limiter.

The operating temperatures must be adhered to.

The  connection  cable  must  be  permanently  installed  up
to  the  inlet  into  the  on-site  junction  box,  taking  the
permissible  bending  radius  =  5  x  outer  diameter  into
consideration.

In  the  dust  Ex  area,  the  applicable  requirements  of
ABNT NBR IEC 60079-14 must be complied with.

Illustration 2: 

Installation example horizontal VARITHERM with

TAE or TS and clearance

Illustration 3: 

Installation example vertical VARITHERM with

TAE or TS with clearance

Additional  installation  material,  such  as  rails  or  panels
and also junction boxes, are not included in the standard
scope of delivery (see 

Installation accessories [

}

Page 4]

)

and must be ordered additionally.

Summary of Contents for CP VARITHERM DBPA









Reviews: