2
Intex ASG18V
intex.com.au
|
intex.co.nz
Thank You for purchasing the Intex Auto Feed Screw Gun.
Manufactured to high standard for dependability, properly
cared for, it will give you years of trouble free performance.
Important:
Carefully read through this entire owner’s manual before
using your new tool. Pay close attention to the Rules for
Safe Operation. Warnings and Cautions. Use your tool
properly and only for what it is intended.
The use of safety symbols in this manual it to attract your
attention to possible dangers. The safety symbols, and the
explanations with them, require your full understanding.
The safety warnings do not by themselves eliminate
any danger, nor are they substitutes for proper accident
prevention measures.
SYMBOL
This Safety Alert Symbol indicates
caution, warning, or danger. Failure to obey a
safety warning can result in serious injury to
yourself or others. To reduce the risk of injury,
fire, or electric shock always follow the safety
precautions.
know your tool
Safe operation of this tool requires that your read and fully
understand this owner’s manual and all labels affixed to
the tool. Learn its applications and limitations as well as the
potential hazards peculiar to a power tool. Keep this
manual readily available for future reference.
IMPORTANT
Servicing of a tool requires extreme care and knowledge and
should be performed only by a qualified service technician.
For service or repair contact and Authorized Service Centre.
CAUTION
Do not attempt to operate this tool
until your have thoroughly read and completely
understood all instructions, safety rules, etc.,
contained in this manual. Failure to comply can
result in accidents involving fire, electric shock,
or serious personal injury. Save the Owner’s
Manual and review frequently for continuing safe
operation and for instructing others who may
use this tool.
When using power tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock, and personal injury,
including the precautions following.
READ ALL INSTRUCTIONS
THOROUGHLY
GENERAL SAFETY PRECAUTIONS
Keep The Work Area clean.
Cluttered work areas and
work benches invite injuries.
Consider Work Area Environment
. Keep work area well
lit. Do not use tool in presence of flammable liquids or gases.
Guard Against Electrical Shock
By Preventing Body
Contact With Grounded Surfaces. For example: pipes,
radiators, ranges, refrigerator enclosures.
Keep children Away
. Do not let visitors contact tool
or extension cord. All visitors should be kept away
from work areas.
Store Idle Tools
. When not in use, tools should be stored
in a dry, high and/or locked place out of the reach of children.
Do Not Force Tool.
It will do the job better and safer at
the rate for which it was intended.
Wear proper Clothing
. Do not wear loose clothing or
jewellery. They can be caught in moving parts. Rubber gloves
and non-skid footwear are recommended when working
outdoors. Wear protective hair covering to contain long hair.
Use Safety Glasses
. Also use face or dust mask if
cutting operation is dusty.
Secure Work.
Use clamps or a vice to hold work.
It is safer than using your hand and it frees both hands
to operate the tool.
Do Not Overreach.
Keep proper footing and balance
at all times.
Maintain Tools With Care.
Keep tools sharp and clean
for better and safer performance. Follow instructions for
lubricating and changing accessories. Keep handles dry,
clean and free from oil and grease.
Disconnect Battery Pack
. When not in use, before
servicing and when changing accessories such as blades,
bits and cutters.
Remove Adjusting Keys And Wrenches.
Form habit
of checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
Avoid Unintentional Starting
. Do not carry the tool with
your finger on the switch. Be sure switch is off when
installing battery pack or bits.
Stay Alert.
Watch what you are doing. Use common
sense. Do not operate tool when your are tired.
Check Damaged Parts
. before further use of the tool, a
guard or other part that is damaged should be carefully
checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting,
and any other conditions that may alter its operation.
Any part that is damaged should be properly repaired or
replaced by an Authorized Service centre. Have defective
switches replaced at an Authorized Service Centre. Do not
use tool if switch does not turn it on and off.
WARNING:
The operation of any tool can result in
foreign objects being thrown into your eyes, which
can result in severe eye damage. Before operating
power tool, always wear safety goggles or safety
glasses with side shields and a full face shield
when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety
glasses with side shields.
General safety rules