background image

341

PO

SAVE THESE INSTRUCTIONS

(341PO)  MODEL SF90110-1 SAND FILTER PUMP  ENGLISH  7.5” X 10.3”  PANTONE 295U  

04/01/2021

English

Page 5

PARTS REFERENCE

Before assembling your product, please take a few minutes to check the contents 

and become familiar with all the parts.

*

If this pump was not purchased as part of a pool set, the above

parts can be ordered at www.intexcorp.com if needed.

Parts shown on this page are supplied with the pool package and 

are shown here for assembly purposes only.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept 
any interference received, including interference that may cause undesired operation. 

WARNING: 

Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment. 

NOTE: 

This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of 
the following measures:

Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.

NOTE:

 Drawings for illustration purpose only. Actual product may vary. Not to scale.

No tools are required for the assembly.

21

22

23

24

25

38

27

21

22

23 24

25

26

28

14 

30

28

29 31

*

*

*

*

37

37

39

34

Summary of Contents for Krystal Clear SF90110-1

























Reviews: