299
NLA
S AVE THESE INSTRUCTIONS
(299NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/07/2018
English
Page 15
OPERATION
On/Off Button:
Once the unit is plugged in, use this button to active the control unit panel buttons. The
light next to the button is green when activated. Press this button to turn off all currently activated functions.
NOTE:
The On/Off button may appear as a black button in the center of the control panel.
Heat Button:
Use this button to activate the heating system. The pump will heat the spa water until the
water temperature reaches the set temperature. When the spa water temperature drops 1-2°C (1.8-3.6°F)
below the set temperature the heating system will restart. When the fl ame icon on the display is red, the
heating system is activated. When the fl ame icon turns green, the water is at the set temperature. The
heating system is at rest and the fi ltration system will continue working nonstop.
NOTE:
To stop the fi ltration system while the heater is at rest mode, press the fl ame button fi rst and then
the
fi lter button. Pressing the fl ame button only while the heater is at rest mode will turn off the heating
system only and the fi ltration system will operate for another 24 hours before it turns off automatically.
Celsius/Fahrenheit Toggle button:
The temperature can be displayed in either Fahrenheit or Celsius. The system’s default is Celsius.
CAUTION:
NEVER use the spa if indicated water temperature is more than 40°C (104ºF).
Temperature Adjustment Buttons:
Pressing the Temperature Increase or Decrease buttons will
cause the LED to fl ash. When fl ashing you can adjust to the desired temperature setting. If you hold these
buttons down the values will rapidly increase or decrease. The new and desired temperature setting will
remain on the LED display for 5 seconds to confi rm the new value.
NOTE:
The default temperature is 20°C (68°F).
NOTE:
Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Water Filter Button:
This button turns the fi lter pump on and off. If the heating system is activated the fi ltration system will
automatically
start.
The
water
fi lter icon on the display is green when activated.
Water Jet Button:
Use this button to activate the jet massage system. After 30 minutes of continues
use, the jet massage system will automatically turn off. The water jet icon on the displays is green when
activated. The angle of the water jet nozzles inside the spa tub wall can be adjusted manually.
WARNING:
Do not run jet system when the cover is attached, air pressure may accumulate inside the spa
and cause irreparable damage and bodily harm.
Bubble Button:
Use this button to activate the massage system, which has a 30-minute auto-shutoff
feature. The bubble icon on the displays is green when activated.
WARNING:
Do not run Bubble system when the cover is attached, air can accumulate inside the spa and
cause irreparable damage and bodily harm.
Sanitizer Button:
Use this button to activate and set operating hours for the sanitation system.
LED Display:
Once plugged in the LED displays the current water temperature automatically.
NOTE:
The built-in hard water treatment function works automatically in conjunction with the fi ltration system.
Jet Nozzle Adjustment
The amount of water and pressure coming out from the jet nozzles can be adjusted by turning the jet
nozzle rim clockwise (maximum water output), counterclockwise (low water output) or anything in between.
Closing one or 2 jet nozzles will divert more water pressure to the other jet nozzles.
A: Heat Button
B: Celsius/Fahrenheit Toggle Button
C: Temperature Increase Button
D: Temperature Decrease Button
E: Water Filter Button
F: Water Jet Button
G: Sanitizer button
H: LED Display
I: On/Off
Button
J: Bubble
Button
SPA CONTROL UNIT PANEL
)
F
J
D
C
B
A
H
G
I
E
-
+
40
C
o
