348
PO
S AVE THESE INSTRUCTIONS
(348PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 10/25/2019
English
Page 4
WARNING
j) Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and unconsciousness. The use of alcohol, drugs, or
medication can greatly increase the risk of fatal hyperthermia. The causes, symptoms, and effects of hyperthermia may be described as
follows:
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of
98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness,
and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness
of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the
danger of drowning.
• People with infectious diseases should not use a spa or hot tub.
• To avoid injury exercise care when entering or existing the spa or hot tub.
• Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause strong fumes or violent reactions and
hazardous chemical spray.
• Never jump or dive into a spa or any shallow body of water.
• Assembly and disassembly by adults only.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
• The plug must be accessible after product is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and other equipment.
• If the supply cord is damaged, it must be replaced by a qualified electrician in order to avoid a hazard. Use only identical replacement parts
when servicing.
• To reduce the risk of electric shock and fire, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to
electrical supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
• Do not leave the spa empty for extended period of time. Do not expose the spa to direct sunlight for extended period of time.
• Provide adequate drainage system around the spa to deal with overflow water and splashes.
• Do not allow the water in the spa to freeze. Do not turn on the spa when the water is frozen.
• Do not use the spa if damaged in delivery and/or malfunctioning in any fashion. Contact the Intex service center for further direction.
• Never pour water with a temperature higher than 104°F (40°C) into the spa directly.
• Keep all pets away from spa to avoid any damage.
• Do not add bath oil or bath salt to the spa water.
• Avoid drowning risk. Keep children away. Children or objects cannot be seen under cover.
• Remove cover completely before entry of bathers – entrapment possible.
• Stay off cover – will not support weight.
• Non-secured or improperly secured covers are a hazard.
• Follow these rules to avoid drowning, or other serious injury.
CAUTION
• Maintain water chemistry in accordance with manufacturer’s instructions.
• This product is provided with a GFCI/RCD located at the end of the power cord. The GFCI/RCD must be
tested before each use. Do not use the spa if the GFCI/RCD does not function properly. Disconnect the
power cord until the fault has been identified and corrected. Contact a qualified electrician to correct the
fault. Do not bypass the GFCI/RCD. There are no serviceable parts inside the GFCI/RCD. Opening the
GFCI/RCD will void the warranty.
1.
Plug the power cord into a grounded electrical socket.
2.
Press the
RESET
button on the GFCI/RCD.
3.
Turn on the spa electrical equipment.
4.
Press the
TEST
button on the GFCI/RCD. The GFCI/RCD indicator
should turn off and the electrical equipment should shut off. If the
GFCI/RCD indicator does not turn off, and the electrical equipment
does not shut off, the GFCI/RCD is faulty. Do not use the spa.
Contact a qualified electrician to correct the fault.
5.
Press the
RESET
button on the GFCI/RCD. The indicator on
the GFCI/RCD should turn on. If the GFCI/RCD indicator does
not turn on, the GFCI/RCD is faulty. Do not use the spa.
Contact a qualified electrician immediately to correct the fault.
WARNING
TEST
RESET
RESET
TEST
TEST
RESET
RESET
RESET
TEST
TEST
