Intimus 120CC3 Operating Manual Download

Page: 7 / 20

MATERIAL JAM IN THE MACHINE:

(Auto reverse function)

If a jam is caused by too much material being fed in

the following happens:

- The cutters jam, then run in reverse for a short

time (material is released) and stop. The motor

switches off. The control display (6) comes

on.

Proceed as follows:

Paper jam in paper feed slot (12)

- Remove the paper that has been fed back.

- The cutters now run forwards automatically and

shred the remaining paper in the cutters. During

the forward run the forward button (3) LED

display comes on. The control display (6)

goes out.

- Continue shredding with less paper.

Material jam in CD/DVD feed slot (13)

Remove the material carefully

because there is the risk of being

injured by the sharp cut surfaces.

- Remove the returned material.

- The remaining material to be cut is now

automatically fed to the cutters again and

shredded. During the forward run the forward

button (3) LED display comes on. The control

display (6) goes out.

- If the material to be cut has gone through continue

shredding with the right amount of material.

- If necessary, switch the cutters manually

alternately from forward to reverse until the

material has gone through completely and been

shredded.

SIMULTANEOUS MATERIAL FEED:

Should material be fed into the two feed slots at the

same time the following happens:

- The cutters jam, then run in reverse for a short

time (material is released) and stop. The motor

switches off. The control display (6) comes

on.

- Take the material out of one of the slots.

- Press the forward button (3) briefly. The material

in the other slot is fed to the cutters and shredded.

The control display (6) goes out.

LIGHT BARRIER COVERED

WHEN DOOR OPENED:

Should there still be material in one of the two feed

slots when the door is opened, the motor switches

off and the cutters stop. The control display (6)

comes on.

Close the door and acknowledge the status by

pressing the forward button (3) briefly. The existing

material is fed to the cutters and shredded.

LIGHT BARRIER COVERED

WHEN MACHINE TURNED ON:

Should there still be material in one of the two feed

slots when the machine is switched on the control

display (6) comes on.

Remove the material and acknowledge the status

by pressing the forward button (3) briefly.

MOTOR PROTECTION:

Should the motor be overloaded it switches off. The

control display (9) comes on.

The machine can be started again after a cooling

down period of about 25 – 40 minutes (depending

on the model and the room temperature).

ELECTRICAL FAULT:

If the control display (9)

flashes

together with

the function button (2) LED display or only the

control display (8)

flashes

there is an electrical

fault. The machine cannot be started.

In this case please contact your dealer.

FAULT CHECK LIST:

Should the machine not work, check the following

points:

- is the

plug

connected to the power supply?

- is the

door

closed?

- is the

paper collection bag

full?

Follow the instructions for “EMPTYING THE

PAPER COLLECTION BAG“.

- Is the

CD/DVD collection container

full?

Follow the instructions for “EMPTYING THE CD/

DVD COLLECTION CONTAINER”.

- Is there a

material jam

in the machine?

Follow the instructions in “MATERIAL JAM IN

THE MACHINE”.

- Is the

motor

overloaded?

See “MOTOR PROTECTION”.

If none of these test points apply, please

contact your dealer.

CUTTER MAINTENANCE (CROSS CUT):

Cross cut cutters must be oiled after a specific

operating time. If the control display (7) comes

on proceed as follows:

Open the door. The control display (8) comes on and
the reverse button (4) LED display as well as the control

display (7)

flashes

. Remove the oil reservoir (17) (Fig. 4)

from the holder in the door and close the door again.

Pour a little oil onto a sheet of paper and then feed this

through the paper feed slot (12) onto the cutters.

The paper is drawn in and in this way the oil is distributed

to the cutters.

Note: This procedure is acknowledged as follows to turn

off the display after the cutters have been oiled:

- Open the door until the control display (8) lights up. The

control displays (7) and (4) flash.

- Press the reverse button (4) and keep it held down until

the control display (7) goes out.

Before starting any repair work and

also before cleaning/maintenance

which is not described in

the following section always

disconnect the mains power

supply!

CLEANING THE PHOTOCELLS:

If paper particles should come to rest in the inlet guide (for

example after a paper jam) it is possible that the machine will

not turn off, due to the broken light barrier.

To remove these paper strips and also to clean the photocell,

pass another sheet of paper through the feed slot, or switch

the machine to reverse and wipe both “eyes” of the photocell

with a brush.

- Close the door again.

The cutters now start a cleaning cycle automatically (forward

and reverse run) and then switch off. The machine is ready

for use again. Should you need to re-order the special oil see

“SPECIAL ACCESSORIES”.

AUTOMATIC ENERGY SAVING:

If the machine is not used for a while it automatically switches

off after about 5 minutes. The function button (2) LED display

for “Ready” goes out. Press the function button briefly to

turn it on again.

DISPOSING OF THE MACHINE:

Dispose of the machine in an environmentally

friendly fashion at the end of its useful service life.

Do not dispose of any of the parts included in the

machine or its packaging with household waste.

153 7 01/16

120 SC2

120 CC3/CC4/CC5/CC6

MALFUNCTIONS

MAINTENANCE / DISPOSING

* based on A4-paper 70g/m² at 230V/50Hz

Model

Power supply data

supply voltage/frequency · current consumption · power

intimus 120SC2

220-230V/50Hz · 7.8 amps · 1.8 kW