Intimus 34 CP7, Operating Instructions Manual

94651 1 11/17

Translation of the Original Operation Manual

Übersetzung der Originalbetriebsanleitung

GB

8

2  Initiation

2 .1  Scope of application

Caution!

Damage to the cutting mechanism!
The machine must only be used to shred 

paper .

Shredding other sorts of data carriers may 

cause damage to the machine (e.g. damage 

to the cutters etc.).

The 

intimus 34 CP7

 data shredder is a machine used 

for shredding general documents.

2 .2  Installation

1 . 

The shredder should be placed on a flat level sur-

face.

2 . 

Make sure that the wastebasket is completely in-

serted into the shredder cabinet and that it fits 

flush with in the cabinet.

3 . 

Plug the power cord into any standard 230-volt AC 

outlet.

4 . 

Depress the ON/OFF button (Fig. 1/1). The READY 

LED (Fig. 1/2) should light up. You are now ready to 

start shredding.

NOTE!

UK adaptor is inside of basket!

3  Operation

Caution!

Damage to the machine!

Do not attempt to operate shredder if the 

shredder is experiencing any kind of problem.

3 .1  Turning the machine on

With the electrical cord plugged in, with the ON/OFF 

button (Fig. 1/1) depressed, and with the shredder 

wastebasket properly in place, the READY LED (Fig. 1/2) 

will light up. This means that the shredder is now ready 

for operation.

3 .2  Operating the shredder

NOTE!

Remove all paper clips and staples from paper 

before shredding.

When paper is inserted into the feed opening, the 

shredding process will start automatically and stop 

when the paper has completed its travel through the 

feed opening.

1

2

5

4

3

6

7

8

000186

1

ON/OFF button

2

Ready LED

3

Overheat LED

4

Overload LED

5

Bin Full LED

6

REVERSE button

7

FORWARD button

8

Feed opening

Fig. 1  Controls intimus 34 CP7

The ON/OFF button (Fig. 1/1) is located on the top of 

the shredder. Also located on top of the shredder is the 

FORWARD and REVERSE buttons (Fig. 1/7+6).

Controls:

„

When the 

ON/OFF button

 (Fig. 1/1) is pressed, the 

shredding process will start when paper is inserted 

into the feed opening and will continue until it has 

passed through the feed opening.

„

The 

REVERSE« button

 (Fig. 1/6) is used to assist 

in the removal of a paper jam, which reverses the 

shredding process prior to a completed forward 

cycle, thus clearing the cutters. When switching 

from REVERSE to FORWARD, always allow the mo-

tor to stop to prevent possible damage to the mo-

tor.

„

The 

ON/OFF position

 (Fig. 1/1) is used to termina-

te the AC power to the shredder. lt is recommen-

ded to turn the shredder off when the shredder is 

not being used for a prolonged period of time.

„

When the 

READY LED

 (Fig. 1/2) is lit, it lets the user 

know that the wastebasket is inserted correctly 

and that the shredder is turned on and ready for 

use. lf the READY LED does not light up, make sure 

that the plug is plugged in, the basket is inserted 

correctly and the ON/OFF is depressed.

„

When the 

overheat LED

 (Fig. 1/3) is lit, turn off 

or unplug the power cord from the AC outlet and 

wait at least 30 minutes . This will allow the motor 

to cool down.