Invacare 65510, Assembly, Installation And Operating Instructions

For more information regarding Invacare products, parts, and services, please visit www.invacare.com

Part No 1163186

1

Rollator

Rollator

Model 65510

SAVE THESE INSTRUCTIONS

DEALER:

These

instructions

MUST

be

given

to

the

user

of

this

product.

NOTE:

Check

ALL

parts

for

shipping

damage.

If

shipping

damage

is

noted,

DO

NOT

use.

Contact

carrier/dealer

for

further

instruction.

WARNING

• DO NOT use this product or any available optional equipment without first completely reading and understanding these 

instructions and any additional instructional material such as owner’s manuals, service manuals or instruction sheets supplied 

with this product or optional equipment. If you are unable to understand the warnings, cautions or instructions, contact a 

healthcare professional, dealer or technical personnel before attempting to use this equipment - otherwise, injury or damage 

may occur.

• Each individual should ALWAYS consult with their physician or therapist to determine proper adjustment and usage.

• DO NOT use the rollator as a wheelchair or transport device. 

• A physical/occupational therapist should assist in the height adjustment for maximum support and correct brake activation.

• Care should be taken to ensure that all hand and height adjustments are secure, and that casters and moving objects are in good 

working order before using this or any mobility aid.

• All casters MUST be in contact with the floor at all times during use. This will ensure the rollator is properly balanced.

• When using the rollator in a stationary position, the hand brakes MUST be locked.

• ALWAYS observe the weight limit on the labeling of your product. Check that all labels are present and legible. Replace if 

necessary.

• The rollator basket and tray have a weight limitation of 11 lbs (5 kg). The tote bag has a weight limitation of 10 lbs (5 kg). Items 

placed in either the basket or the bag should NOT protrude from the basket or bag.

• If push handles are exposed to extreme temperature (above 100°F or below 32°F), high humidity and/or becomes wet, prior to 

use, ensure hand grips DO NOT twist on rollator handle - otherwise damage or injury may occur.

• After installation and before use, ensure that all attaching hardware is tightened securely.

• DO NOT hang anything from the frame of the rollator. Items should be placed in the basket or the tote bag.

ACCESSORIES WARNING

• Invacare products are specifically designed and manufactured for use in conjunction with Invacare accessories. Accessories 

designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products.

Assembling the Rollator

NOTE:

For

this

procedure,

refer

to

FIGURE 1.

1.

Remove

plastic

caps

from

the

side

frame

tubes.

2.

Unfold

the

rollator

and

engage

the

locking

mechanism

between

the

front

frame

tubes.

Refer

to

Detail

“A”.

NOTE:

The

locking

lever

and

washer

are

installed

on

the

outside

of

the

frame

tubes.

3.

From

the

inside

of

the

frame,

put

the

bolt

through

the

locking

lever

mounting

holes.

Refer

to

Detail

“B”.

4.

Put

a

washer

onto

the

bolt.

5.

Thread

the

locking

lever

onto

the

bolt.

DO

NOT

tighten

the

locking

lever.

6.

Repeat

STEPS

3

‐

5

to

install

the

opposite

locking

lever.

7.

On

both

sides

of

the

rollator,

insert

and

adjust

the

handle

to

the

appropriate

height.

Tighten

the

locking

lever

onto

the

bolt.

WARNING

The handles MUST NOT be angled outside the marked 

position as this reduces the rollators lateral stability. Refer to 

Detail “C”.

Adjusting Handle Height

1.

On

both

sides

of

the

rollator,

loosen,

but

DO

NOT

remove,

the

locking

levers.

2.

Adjust

each

handle

to

the

appropriate

height

and

tighten

the

locking

lever.

Make

sure

both

handles

are

adjusted

to

the

same

height.

Removing the Handles

1.

On

each

side

of

the

rollator,

loosen

but

DO

NOT

remove

the

locking

lever.

2.

Remove

the

handles

from

the

frame

tubes.

Installing the Bag, Basket and Tray

NOTE:

For

this

procedure,

refer

to

FIGURE 1,

Detail

“D”.

NOTE:

To

remove

the

bag,

basket

and

tray,

reverse

these

procedures.

Bag

Hang

the

bag

between

the

rollator

frame

tubes

and

secure

with

snap

button

flaps.

Basket

Install

the

basket

onto

the

hooks

on

the

rollator

frame.

Tray

Put

the

tray

in

place

on

top

of

the

basket.

FIGURE 1   

Assembling the Rollator

Assembly, Installation and Operating Instructions

DETAIL “B”

Basket

Tray

Bag

DETAIL “D”

Locking 

lever

Bolt

Locking Lever 

Mounting Hole

Handle

Push down to engage locking 

mechanism between frame tubes

DETAIL “A”

Incorrect

Correct

DETAIL “C”