5 Accessories
5.1 List of available accessories
•
Side rails
– Scala Basic 2
3/4 length collapsible steel side rail (168 cm x 40 cm), mounted
on the side tube. Release button in the head section
– Scala Basic Plus 2
3/4 length collapsible steel side rail (168 cm x 40 cm), mounted
on the side tube. Release button in the head section
– Scala Medium 2
3/4 length collapsible steel side rail (165 cm x 46 cm), mounted
on the side tube. Release button in the head section
– Scala Decubi 2
3/4 length collapsible steel side rail (168 cm x 54 cm), mounted
on the side tube. Release button in the head section
– Britt V
Full length side rail (205 cm x 40 cm) in wood, mounted on
the bed end rail. Two centered release buttons for folding
of the gate
– Line standard
Full length side rail (206 cm x 40 cm) in aluminum or wood
finish, mounted on the bed end rail. Two centered release
buttons for folding of the gate
– Line extendable
Full length side rail with telescopic extension (206-226 cm x
40 cm) in aluminum or wood finish, mounted on the bed end
rail. Two centered release buttons for folding of the gate
•
Mattress support extension – 10 cm
•
Mattress support extension – 20 cm
•
Lifting pole
•
Transport fitting
•
Hand control with tilt, HB84
•
Hand control with tilt, HL84, with integrated ACP function
•
Backup battery and battery box
Important
–
Use only original accessories and spare parts. Spare
parts lists and extra user manuals can be ordered from
Invacare
or via homepage.
5.2 Side rails
WARNING!
Risk of entrapment or suffocation
There’s a risk of entrapment of suffocation between
mattress support, side rail and bed end.
–
Always ensure correct fitting of the side rails.
Steel side rails
WARNING!
Risk of entrapment
There’s a risk of entrapment of suffocation between
mattress support, side rail and bed end.
–
When using steel side rails, always make sure that the
distance between the bed end and the side rail’s handle
upper edge is less than 6 cm in the head end and more
than 32 cm in the foot end of the bed.
A sticker is placed on the side rail to indicate the minimum space
between side rail and the head end of the bed:
CAUTION!
There’s a risk of entrapment of fingers on assembly and
operation of the side rail.
Mounting and dismounting
The side rail must be mounted with the release system at the head
end of the bed.
1.
Mounting
The fork links on the side rail must be mounted according to
the instruction on the side rail.
Tighten the side rail with the two finger screws.
2.
Dismounting
Loosen the two finger screws and remove the steel side rail.
Operating
1
.
2.
1.
Up: Lift and pull the top bar of the side rail towards the end with
the locking mechanism.
Ensure, it is locked in place.
2.
Down: Press the release button and push the top bar of the side
rail away from the locking mechanism
CAUTION!
If the side rail is not locked properly it can fall down.
–
Pull/push the top bar of the side rail to ensure that the
locking system is properly engaged.
Line and Britt V side rails
WARNING!
Risk of entrapment / suffocation
–
To avoid the patient from entrapping or accidentally
falling from the mattress support, it is essential that
the gliding shoes are correctly guided into the bed end
rails. Adjust the side rail bars by hand, to ensure they
are mounted correctly.
Mounting
CAUTION!
–
Make sure that the straps between the rails are not
damaged or loose.
1.
Mount one end at a time. Lift the upper side rail bar (the release
buttons must face up/outwards)
2.
Press the locking pin at the end of the side rail with a finger.
3.
All three gliding shoes at the end of the bars are guided into
the bed end rail, until the lower bar has been locked, thereby
preventing the side rail from falling down.
4.
Repeat points 2 and 3 when mounting the other end of the side
rail.
1567454-A
9
Summary of Contents for Etude Plus
Page 18: ...Notes...
Page 19: ...Notes...
