background image

2

WARNING

THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED

BY AN AUTHORIZED DEALER OR QUALIFIED SERVICE

TECHNICIAN.

DO NOT INSTALL OR USE THIS EQUIPMENT WITHOUT FIRST

READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE

UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND

INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL,

DEALER OR TECHNICAL PERSONNEL IF APPLICABLE BEFORE

ATTEMPTING TO INSTALL OR USE THIS EQUIPMENT -

OTHERWISE INJURY OR DAMAGE MAY RESULT.

NOTICE

THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

SAVE THESE INSTRUCTIONS

WARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices
which could result in personal injury or property damage.

SPECIAL NOTES

SPECIAL NOTES .............................................. 2

SAFETY SUMMARY .......................................... 3

IMPORTANT INFORMATION ........................... 5

INSTALLATION/ADJUSTMENT OVERVIEW .... 5

PROCEDURE 1 - PREPARING

WHEELCHAIR ................................................ 6

INSTALLING/REMOVING CANE CLAMPS ........... 6
INSTALLING INSERTS ........................................ 6

PROCEDURE 2 - PREPARING THE INFINITY

BACK FOR INSTALLATION ........................... 7

INSTALLING/REMOVING THE

LATERAL SUPPORTS .................................... 7

INSTALLING/REMOVING CUSHIONS ................. 7
ADJUSTING THE MOUNTING HARDWARE ....... 9

TABLE OF CONTENTS

PROCEDURE 3 - INSTALLING/REMOVING

THE INFINITY BACK ................................ 10

INSTALLING/REMOVING THE INFINITY BACK .. 10

PROCEDURE 4 - ADJUSTING THE

INFINITY BACK ......................................... 11

ADJUSTING CANE CLAMP HEIGHT ................. 11
ADJUSTING THE HINGE/ANGLE

(DUALFLEX ONLY) ..................................... 11

ADJUSTING THE DEPTH HARDWARE ........... 12
ADJUSTING THE LATERAL SUPPORTS ......... 12

PROCEDURE 5 - MAINTENANCE ................. 14

INSTALLING/REMOVING CUSHION FOAM ....... 14
INSPECTION .................................................... 15
CLEANING ....................................................... 15

LIMITED WARRANTY ................. BACK COVER

S
P
E

C

I

A

L

N
O

T

E
S

C
O
N

T

E

N

T

S

SPECIAL NOTES/TABLE OF CONTENTS

Summary of Contents for Infinity Back Support

















Reviews: