background image

17

Invacare Ltd warrants each of its products to perform 
in accordance with established specifications for 
the following time periods, starting from the date the 
product is shipped from Invacare Ltd. 

Control Units   2 years 
Soft Goods 

2 years

During the warranty period, Invacare Ltd either directly 
or through its distributors, will repair or replace at 
no charge, any products that are not performing in 
accordance with established specifications, unless the 
problem/ failure is due to:

• 

customer damage, negligence and/ or misuse

• 

unauthorised repairs 

Items not covered under warranty include, but are 
not limited to, stains, punctures, cuts, damages 
to electrical cords, rips or tears, dents and/ or lost/ 
missing parts.

All products returned for warranty repairs must be 
assigned a Return Autho risation Number prior to 
return. Returns should include information describing 
the problem and or requested repair and be sent 
to your local Invacare Ltd sales office by prepaid 
transportation. Invacare Ltd will return the repaired/
replaced product at no charge. Warranty repairs do not 
extend the length of the warranty period. 

Neither Invacare Ltd, its distributors, officers, directors, 
employees or agents shall be liable for consequential 
or other damages, including but no limited to personal 
injury, loss, or any other expense, directly or indirectly 
arising from the use of its products. The sole remedy 
for breach of the limited warranty granted herein shall 
be repair or replacement or the Invacare Ltd products.

                                                                                                                                                                                                                                 Warranty Information

Product life Cycle

The product life cycle quoted can be exceeded if the 
product is maintained as per Invacare maintenance 
and cleaning guildlines, The life cycle can also be 
considerably reduced if the guildlines for maintenance 
and cleaning are not followed or by unintended use

Summary of Contents for SoftAir EXCELLENCE



















Reviews: