101
PROCEDURE 17
FWD WHEELCHAIRS
ADJUSTING WEIGHT
DISTRIBUTION (FIGURE 13)
NOTE: Depending on the seat depth ordered, the position
of the seat support brackets is factory set between 2.25 and
6 inches (measured from the front of the base frame to the
front of the seat support brackets). This will put approximately
65% of the total weight of the chair and user over the drive
wheels (large wheels), allowing for the best performance of
the chair.
In order to achieve maximum comfort and maneuverability
for the end user, it may be necessary to adjust the seat
support brackets slightly forward or backward. It is recom-
mended that the seat support brackets be set as close to
2.25 - 6 inch mark (depending on seat depth) as possible,
while allowing maximum comfort and maneuverability to
the end user.
Adjusting Weight Distribution For New Seat
Depth
NOTE: When changing the seat depth of the chair, it is
necessary to adjust the seat support brackets in order to
achieve optimum weight distribution (65%). Perform the
following procedure to adjust the seat brackets:
1. Refer to the following chart to determine the correct
position of the two (2) seat support brackets to achieve
optimum weight distribution (65%).
2. Loosen the four (4) mounting screws that secure the
two (2) seat support brackets to the base frame.
3. Adjust the two (2) seat support brackets forward or
backward until the position determined in STEP 1 is
achieved.
NOTE: When the front of the seat aligns with the controller,
approximately 65% of the total weight of the chair and user is
over the drive wheels (large wheels).
4. Adjust the two (2) seat brackets slightly forward or
backward, until maximum comfort and maneuver-
ability for the end user is acheived.
5. Retighten the four (4) mounting screws securing the
two (2) seat support brackets to the base frame.
Seat Support
Brackets
Mounting Screws
Seat
Depth
(Inches)
Position Of The Seat Support
Brackets (Inches) To Achieve
Optimum Weight Distribution (65%)
14 to 16 inches
2.25-inches
17 to 18 inches
4.25-inches
19 to 20 inches
6-inches
INSTALLING 90
o
FOOTBOARD
(FIGURE 14)
WARNING
DO NOT remove detent pin from footrest
assembly. Otherwise, injury may result.
1. Remove the existing footrests. Refer to FRONT RIG-
GINGS in PROCEDURE 3 of the Owners manual,
part number 1081227.
2. Remove the telescoping front rigging supports. Refer
to ADJUSTING/REPLACING TELESCOPING
FRONT RIGGING SUPPORT in PROCEDURE 3 of
the Owners Manual, part number 1081227.
3. Remove existing front and rear shrouds. Refer to RE-
MOVING/INSTALLING THE REAR SHROUD and
REMOVING/INSTALLING THE FRONT SHROUD in
this procedure of the Manual.
4. Remove the seat. Refer to REMOVING/INSTALLING
THE SEAT FRAME in PROCEDURE 6 of this Manual.
5. Position the 90
o
footboard on the base frame as shown
in FIGURE 14.
6. Loosely install one (1) mounting screw into the back
of the footboard and into the base frame.
7. Loosely install two (2) mounting screws and washers
through the top of the footboard and into the base frame.
8. Torque all three (3) mounting screw between 15 and
19-foot pounds.
Front Of
Base
Frame
FIGURE 13 - ADJUSTING WEIGHT
DISTRIBUTION
2.25 Inches (For a
seat depth of 14 to
16 inches)
NOTE: Seat/seat frame not shown for clarity.
F
W
D
W
H
E
E
L
C
H
A
I
R
S
Summary of Contents for Storm Arrow
Page 105: ...105 NOTES NOTES N O T E S...
Page 106: ...106 NOTES NOTES N O T E S...
