65
Gas Cylinder
Rod
Jam Nut
Gas
Cylinder
NO Movement in Operator
of the Recliner Cable
Assembly
Gas Cylinder
Rod Threads
Handle
No Slack
in Cable
FIGURE 4 - REPLACING/ADJUSTING GAS CYLINDERS
Handle
Cable Fitting
Seated Properly
Pivot Block
Cable
Snapped
into Slot
Nylon Washer
Locknut
Washer
Mounting
Screw
Mounting Bracket
If slack in the recliner cable or movement in the operator of
the cable assembly can not be eliminated, DO NOT use
the recliner cable assembly.
6. Screw the NEW gas cylinder into the operator of the
cable assembly until the jam nut sits on the pivot block,
there is no slack in recliner cable and there is no move-
ment in the operator of the recliner cable assembly.
7. Visually inspect the handle to make sure that the cable
is snapped completely into slot in handle and cable
fitting is seat properly in the handle.
8. Press the operator of the recliner cable assembly to
extend the NEW gas cylinder.
9. Line up the mounting holes of the NEW gas cylinder
and the bracket of the back cane.
10. Reinstall the mounting screw through the mounting
bracket of the back cane, nylon washer, NEW gas
cylinder, nylon washer, mounting bracket and washer
and securely tighten with the existing locknut. Torque
to 75-inch pounds.
11. Adjust the NEW gas cylinders. Refer to ADJUSTING
GAS CYLINDERS in this procedure of the manual.
R
E
C
L
I
N
E
R
10. Visually inspect the handle to make sure that the cable
is snapped completely into slot in handle and cable fit-
ting is seat properly in the handle.
11. Reinstall the mounting screw through the mounting
bracket of the back cane, nylon washer, gas cylinder,
nylon washer, mounting bracket and washer and se-
curely tighten with the existing locknut. Torque to 75-
inch pounds.
12. Line up the mounting hole in the handle of the recliner
cable assembly with the mounting hole in the back cane.
13. Insert the pan screw through the handle of the recliner
cable assembly and the back cane and torque to 9-inch
pounds.
14. Tie wrap the recliner cable assembly to the recliner back
cane.
15. Adjust the gas cylinder. Refer to ADJUSTING GAS
CYLINDERS in this procedure of the manual.
REPLACING/ADJUSTING GAS
CYLINDERS (FIGURE 4)
WARNING
Replace ONE (1) gas cylinder at a time to avoid
injury.
Both gas cylinders MUST be operational and ad-
justed properly BEFORE using the recliner. DO NOT
operate the recliner if only one (1) of the gas cylin-
ders is operational or adjusted properly.
Replacing Gas Cylinder
1. Remove the mounting screw, washer, nylon washers
and locknut that secure the TOP of the gas cylinder to
mounting bracket on back cane.
2. Loosen the jam nut on existing gas cylinder rod.
3. Unscrew the existing gas cylinder from the operator of
the recliner cable assembly and the pivot block and
remove the existing gas cylinder from the wheelchair.
4. Screw cylinder rod of the NEW gas cylinder into the
pivot block until the threads of the cylinder rod are flush
with inside of pivot block (FIGURE 4).
5. With the operator of the recliner cable assembly on
the inside of the recliner seat frame, line up the mount-
ing hole in the operator of the recliner cable assembly
with the new gas cylinder rod.
CAUTION
DO NOT force the gas cylinder rod into the opera-
tor of the recliner cable assembly.
DO NOT cross thread the operator of the recliner
cable assembly with the gas cylinder.
PROCEDURE 14
RECLINER
Summary of Contents for Storm Arrow
Page 105: ...105 NOTES NOTES N O T E S...
Page 106: ...106 NOTES NOTES N O T E S...
