background image

LIMITED WARRANTY

PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW 
APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser who purchases this product when new and unused 
from Invacare or a dealer. This warranty is not extended to any other person or entity and is not transferable 
or assignable to any subsequent purchaser or owner. Coverage under this warranty will end upon any such 
subsequent sale or other transfer of title to any other person.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to 
state.
Invacare warrants the side frames and cross members of this product when purchased new and unused to be 
free from defects in materials and workmanship for a period of five (5) years from the date of purchase from 
Invacare or a dealer, with a copy of the seller’s invoice required for coverage under this warranty. Invacare 
warrants the upholstered materials (seat, back and armrests of the arm assembly) and remaining 
components of this product when purchased new and unused to be free from defects in materials and 
workmanship for a period of thirteen (13) months from date of purchase from Invacare or a dealer, with a 
copy of the seller’s invoice required for coverage under this warranty. If within such warranty periods any 
such product shall be proven to be defective, such product shall be repaired or replaced, at Invacare’s option. 
This warranty does not include any labor or shipping charges incurred in replacement part installation or 
repair of any such product. Invacare’s sole obligation and your exclusive remedy under this warranty shall be 
limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare product. In the 
event you do not receive satisfactory warranty service, please write directly to Invacare at the address at the 
bottom of this page. Provide dealer’s name, address, the product model number, date of purchase, indicate 
nature of the defect and, if the product is serialized, indicate the serial number. Do not return products to our 
factory without our prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL 
NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED, PRODUCTS 
SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION, MAINTENANCE OR STORAGE, 
PRODUCTS MODIFIED WITHOUT INVACARE’S EXPRESS WRITTEN CONSENT INCLUDING, BUT 
NOT LIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR 
ATTACHMENTS; PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT 
WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A PRODUCT DAMAGED BY 
CIRCUMSTANCES BEYOND INVACARE’S CONTROL, AND SUCH EVALUATION WILL BE SOLELY 
DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR 
OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS.
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES 
WHATSOEVER, WHETHER EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR 
VIOLATIONS OF ANY WARRANTY WHATSOEVER, SHALL BE LIMITED TO REPAIR OR 
REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. 
THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND 
THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN. INVACARE SHALL NOT BE 
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR 
CONSEQUENTIAL DAMAGE, OR LIMITATION OF HOW LONG AN IMPLIED WARRANTY LASTS, SO 
THE ABOVE EXCLUSION AND LIMITATION MAY NOT BE APPLICABLE.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND 
REQUIREMENTS.

Invacare Corporation

www.invacare.com

USA

One Invacare Way

Elyria, Ohio USA

44036-2125

800-333-6900

Canada

570 Matheson Blvd E Unit 8

Mississauga Ontario

L4Z 4G4 Canada

800-668-5324

All rights reserved. Trademarks are 

identified by ™ and ®. All trademarks are 

owned by or licensed to Invacare 

Corporation unless otherwise noted.

Teflon is a registered trademark of 

DuPont.

© 2007 Invacare Corporation

Part No. 1110558
Rev E - 12/07

Summary of Contents for Tracer IV





















































Reviews: