background image

14

15

OPERATION

OPERATION

14

15

aV ALD ventilation device | Operating and cleaning instructions 

aV ALD ventilation device | Operating and cleaning instructions

4.1 

Cleaning / replacing the dust filter

The dust filters included in the scope of supply are reusable and can be washed under warm 

running water.

 

Replace excessively dirty or defective filters!

ALD 100 / Light ALD inner cover

 

Carefully release the inner cover from the locking 

hooks in the lower and then the upper section of 

the casing.

 

► Then pull the filter cartridge out of the wall sleeve.

 

► Remove the dirty filter from the filter cartridge.

 

► Clean the dust filter under warm running water.

 

► Wait until the dust filter is completely dry 

or

 dispose 

of the dust filter if it is defective.

 

Insert the cleaned 

or

 a new dust filter into the filter 

cartridge.

 

► Slide the filter cartridge into the wall sleeve flush 

with the interior wall

 

You have cleaned / changed the dust filter

Once the filter has been removed, access to 

the wall sleeve (aV100 ALD) and/or sound 

insulation lining (aV160 ALD) is clear.

 

Before the dust filter and filter cartridge are 

inserted again, wipe out the wall sleeve 

 

(aV100 ALD) and/or sound insulation lining 

(aV160 ALD) with a damp cloth

i

i

Summary of Contents for aV100 ALD















Reviews: