background image

22

23

INSTALLATION AND ASSEMBLY

INSTALLATION AND ASSEMBLY

iV-Compact ventilation system 

 Installation and operating instructions

iV-Compact ventilation system 

 Installation and operating instructions

4.5 

Installing the weather protection hood

NOTE

Installation on an unfinished exterior wall

results in damage to the exterior wall!

• 

Only install the weather protection hood (exterior closure) once the exterior wall is finished 

and completely hardened.

NOTE

Penetration of condensate and/or algae build-up around the weather protection hood

results in damage to the masonry/exterior wall and/or discoloration of the façade!

• 

Affix all sealing tapes prior to installing the weather protection hood base plate.

•  Carry out a biocide/water-repellent pre-treatment on the render around the weather protection 

hood in vulnerable areas (Consult your planner for further information!).

Spirit level, pen, drilling machine with drill bit Ø 8 mm, electrical screwdriver, wall plugs 

(insulation plugs when using Simplex or with insulated exterior walls), permanently 

elastic outdoor sealant, sealing tape, screws

Requirements: 

The 

exterior wall is finished and level.

 

The wall sleeve is fitted.

 

Remove the protective disc from the wall sleeve 

on the exterior wall side.

 

Push the base plate onto the protruding wall sleeve.

Observe

 the alignment of the drip rails: The slope 

leads in direction of the ground/bottom.

 

Align the base plate using a spirit level.

 

Mark out the four bore holes for fastening the base 

plate.

NOTE: 

Damage to the masonry/external 

wall due to misaligned drip rails!

•  Make sure that the slopes on both drip rails 

are aligned to down-facing.

Ö

The weather protection hood is installed.

 

Drill the four holes with Ø 8 mm to a depth of min. 

50 mm.

 

Insert the wall plugs into the drill holes.

 

Secure weather protection hood base plate to the 

external wall using four screws.

TIP:

 When screwing the base plate of Compact pro-

tective hood to external walls with insulation or when 

using the WEB wall installation block/ Simlex wall 

build-in system use insulation plugs to ensure safe 

fastening. These are not part of the scope of supply, 

but are available as an option

.

 

Hook the cover of the from the front into the lateral 

screws (blue arrows) of the base plate.

Make sure

 that the washers are placed between 

the cover and the screw.

 

Pull down the cover until it snaps into place.

 

Secure the cover to the base plate using the lateral 

screws.

 

Turn the four lateral screws together with captive 

washers loosely from the outside into the four 

threaded holes (blue arrows) on both sides of the 

base plate.

ø = 8 mm

50 mm

 

Affix the sealing tape, 9 mm, on the external wall 

side and circumferiantally to the base plate: 

• around the opening for the wall sleeve. 

• at a distance of 5 mm from the outer edge.

Make sure that 

the sealing tape does not protrude 

over the inside edge of the wall sleeve opening.

TIP:

 

Apply the sealing tape only immediately before 

mounting the base plate. 

This prevents excessive expanding of the sealing tape 

and facilitates installation.

4 x

4 x

Summary of Contents for iV-Compact


























Reviews: