background image

30

31

CLEANING AND MAINTENANCE

CLEANING AND MAINTENANCE

iV-Compact ventilation system 

 Installation and operating instructions

iV-Compact ventilation system 

 Installation and operating instructions

Cleaning and maintenance

CAUTION

Cleaning by children and persons with limited abilities.

Injury to body parts (rotating fan) and/or malfunction of the ventilation system!

•  Cleaning/maintenance of the ventilation unit must not be carried out by children and/or persons 

who are not fully capable of doing so due to their physical, sensory or mental capabilities, 

inexperience or lack of knowledge. Young children should be supervised to ensure that they do 

not play with the unit.

The iV-Compact ventilation units and the sMove controller are virtually maintenance-free. 

Any necessary cleaning or maintenance work can be carried out by the user by following these 

instructions.

TIP:

 

Before performing cleaning or maintenance tasks, disconnect the controller's power sup-

ply and put on gloves.

Detergents

NOTE

The plastic/glass surface of the inner panel is not scratch-resistant 

and may be damaged.

•  Do not use sand, soda, acid or chlorine-based cleaning agents.

A commercially available detergent in warm water can be used for cleaning. The following tools 

may be used for cleaning:

•  lint-free, soft cloth

•  soft brush

•  Vacuum cleaner

Recommended maintenance

The maintenance tasks and intervals listed here are recommended by inVENTer GmbH to 

maintain the functionality and performance of the iV-Compact ventilation system.

Depending on requirements and/or air quality, your personal maintenance plan may deviate 

from these recommendations.

Interval

Assembly

Maintenance activity

Cleaning from the interior room

Monthly

Pollen filter

Replace the contaminated pollen filter.

Inner cover

Clean the surface of the panel with a damp cloth.

Quarterly

Dust filter

Wash the dust filter with warm water and 

 

detergent.

Or 

Replace defective dust filters.

Interval

Assembly

Maintenance activity

Half-yearly

Thermal  

accumulator

Remove the thermal accumulator and clean it 

under running warm water.

Guiding vanes

Remove the guiding vanes from the fan.

Clean the guiding vanes using a soft brush or 

under warm running water.

Reversible fan

Clean the fan blades with a brush. 

Wall sleeve

Clean the surface of the wall sleeve with a damp 

cloth.

Carbon filter

Replace the activated carbon filter.

Sound protector

Replace the sound protector.

Sound absorbing insert

Gently pat off the sound absorbing insert.

Yearly

Wind protection insert

Wash the wind protection insert with warm water 

and detergent.

Inner cover base plate

Clean the surface of the base plate with a damp 

cloth.

Cleaning from the exterior

Yearly

Exterior closure:  

weather protection hood 

Clean the surface of the protective hood with a 

damp cloth.

Clean the protective grid on the upper and bottom 

air outlet to ensure the fins between the louvres 

are free.

6.1 

Remove the inner cover panel

To clean and maintain the ventilation unit, first remove the panel of the inner cover.

Requirements: The ventilation unit is switched off.

 

Open the inner cover (

 5.1).

 

Press the side detent lugs inwards on the inner 

cover base plate's spacers.

 

Pull the inner cover panel forwards.

Ensure 

that all the spacers disengage.

 

Remove the inner cover panel from the front.

Ö

You have removed the panel of the inner cover.

CLICK

Summary of Contents for iV-Compact


























Reviews: