Invertek Optidrive Eco ODV-3-220043-1F12-TN, User Manual

74

   |   Optidrive Eco User Guide   |   

Version 3.06

www.invertekdrives.com

Fault 

Code

No.

OLED Message

Description

Corrective Action

Ft-

13

Excessive DC ripple

Excessive DC Ripple 

on Internal DC bus

The DC Bus Ripple Voltage level can be displayed in parameter P0-16.
A historical log is stored at 20ms  intervals prior to a trip in parameter P0-37.
Check all three supply phases are present and within the 3% supply voltage 

level imbalance tolerance.
Reduce the motor load.
If the fault persists, contact your local Invertek Drives Sales Partner.

P-o

14

Input phase loss

Input phase missing 

trip

Drive intended for use with a 3 phase supply, one input phase has been 

disconnected or lost.

h -

15

Hardware detected 

Instant over current

Instantaneous over 

current on drive 

output

Refer to fault 3 above.

th-Ft

16

Thermistor Fault

Faulty thermistor on 

heat-sink

Refer to your Invertek Sales Partner.

t-F

17

I/O processor data 

error

Internal memory fault Parameters not saved, defaults reloaded.

Try again. If problem recurs, refer to your IDL Authorised Distributor.

-F

18

4-20mA signal out 

of range

4-20mA Signal Lost

The reference signal on Analog Input 1 or 2 (Terminals 6 or 10) has dropped 

below the minimum threshold of 3mA when signal format is set to 4-20mA. 

Check the signal source and wiring to the Optidrive terminals.

t-

19

M/C processor 

data error

Internal memory fault Parameters not saved, factory defaults are reloaded.

If problem reoccurs, refer to your IDL Authorised Distributor.

-e

20

User Parameter 

Default

User Parameter 

Defaults

User Parameter default has been loaded. Press the Stop key. Three button 

default – see section 

5.5. Parameter Factory Reset / User Reset

.

F-Pt

21

Motor PTC over heat Motor PTC Over 

Temperature

The connected motor PTC device has caused the drive to trip (analog input 2 

configured for PTC device).

F-F

22

Cooling Fan Fault

Cooling Fan Fault

Check and if necessary, replace the drive internal cooling fan.

-het

23

Ambient Temperature 

High

Ambient Temperature 

too High

Ensure the drive internal cooling fan is operating.
Ensure that the required space around the drive as shown in sections 

3.6. 

Guidelines for Enclosure mounting (IP20 Units)

 thru 

3.8. Guidelines for 

Mounting (IP55 Units)

 has been observed, and that the cooling airflow path to 

and from the drive is not restricted.
Increase the cooling airflow to the drive.
Reduce the effective switching frequency setting in parameter P2-24.
Reduce the load on the motor / drive.

-toq

24

High motor current

Motor current above 

configured profile

Current Monitoring Function has detected motor current levels above the 

normal operating condition for the application.
Check mechanical load has not changed and that the load is not jammed or 

stalling.
For pump application check for potential pump blockage.
For fan applications check airstream to and from the fan is not restricted.

-oq

25

Low motor current

Motor current below 

configured profile

Current Monitoring Function has detected motor current levels below the 

normal operating condition for the application.
Check for mechanical breakages causing loss of load (e.g. belt break).
Check motor has not become disconnected from the drive.

t-F

26

Drive Output Fault

Drive output fault

Drive output fault.
Check for loose motor cables at the drive and at the motor or any termination 

in between. Otherwise refer to your IDL Authorised Distributor.

Sto-F

29

Internal STO circuit 

Error 

Refer to your Invertek Sales Partner

tF-

40

Autotune fail 1

Autotune Failed

Measured motor stator resistance varies between phases. Ensure the motor 

is correctly connected and free from faults. Check the windings for correct 

resistance and balance.

tF-

41

Autotune fail 2

Measured motor stator resistance is too large. Ensure the motor is correctly 

connected and free from faults. Check that the power rating corresponds to the 

power rating of the connected drive.

tF-

42

Autotune fail 3

Measured motor inductance is too low. Ensure the motor is correctly 

connected and free from faults.

tF-

43

Autotune fail 4

Measured motor inductance is too large. Ensure the motor is correctly 

connected and free from faults. Check that the power rating corresponds to the 

power rating of the connected drive.

tF-

44

Autotune fail 5

Measured motor parameters are not convergent. Ensure the motor is correctly 

connected and free from faults. Check that the power rating corresponds to the 

power rating of the connected drive.

12

Tr

oublesh

ooting