InWin SK-Series User Manual Download

Page: 3 / 16

Model : SK-Hybrid BP Series User’s Manual

PAGE 3 OF 16

TABLE OF CONTENTS



Overview ......................................................................................................... 4

Physical Outlook ................................................................................................................... 4

Mechanical ........................................................................................................................... 5



Connector Locations and LED Indicators .................................................... 6

Bottom Connector and Pin Definitions .................................................................................. 7

Top Connectors and LED Indicators ..................................................................................... 8



Hardware Specification ................................................................................. 9



LED Behavior ............................................................................................... 10

Disk Bay LED.......................................................................................................................10

System Alarm LED ...............................................................................................................12



Smart Fan Control ........................................................................................ 13



Firmware Upgrade ....................................................................................... 15

Summary of Contents for SK-Series

















Search results

Summary of Contents for SK-Series

Reviews:

Related manuals for SK-Series

Brands by name

Popular brands

InWin SK-Series, User Manual

Search results

Summary of Contents for SK-Series

Reviews:

Related manuals for SK-Series

Brands by name

Popular brands