1 7
1 7
1 7
1 7
1 7
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
ELECTRICAL CONNECTIONS
WARNING
WARNING
WARNING
WARNING
WARNING
BEFORE CARR
BEFORE CARR
BEFORE CARR
BEFORE CARR
BEFORE CARRYING OUT ANY WORK ON THE EQUIPMENT
YING OUT ANY WORK ON THE EQUIPMENT
YING OUT ANY WORK ON THE EQUIPMENT
YING OUT ANY WORK ON THE EQUIPMENT
YING OUT ANY WORK ON THE EQUIPMENT,,,,,
MAKE SURE THA
MAKE SURE THA
MAKE SURE THA
MAKE SURE THA
MAKE SURE THAT THE ELECTRICAL POWER SUPPL
T THE ELECTRICAL POWER SUPPL
T THE ELECTRICAL POWER SUPPL
T THE ELECTRICAL POWER SUPPL
T THE ELECTRICAL POWER SUPPLY IS
Y IS
Y IS
Y IS
Y IS
DISCONNECTED AND THA
DISCONNECTED AND THA
DISCONNECTED AND THA
DISCONNECTED AND THA
DISCONNECTED AND THAT THERE IS NO POSSIBILITY OF
T THERE IS NO POSSIBILITY OF
T THERE IS NO POSSIBILITY OF
T THERE IS NO POSSIBILITY OF
T THERE IS NO POSSIBILITY OF
THE UNIT BEING ST
THE UNIT BEING ST
THE UNIT BEING ST
THE UNIT BEING ST
THE UNIT BEING STAR
AR
AR
AR
ARTED INAD
TED INAD
TED INAD
TED INAD
TED INADVER
VER
VER
VER
VERTENTL
TENTL
TENTL
TENTL
TENTLY
Y
Y
Y
Y.....
NON-COMPLIANCE WITH THE ABOVE INSTRUCTIONS CAN
NON-COMPLIANCE WITH THE ABOVE INSTRUCTIONS CAN
NON-COMPLIANCE WITH THE ABOVE INSTRUCTIONS CAN
NON-COMPLIANCE WITH THE ABOVE INSTRUCTIONS CAN
NON-COMPLIANCE WITH THE ABOVE INSTRUCTIONS CAN
LEAD T
LEAD T
LEAD T
LEAD T
LEAD TO INJUR
O INJUR
O INJUR
O INJUR
O INJURY OR DEA
Y OR DEA
Y OR DEA
Y OR DEA
Y OR DEATH B
TH B
TH B
TH B
TH BY ELECTROCUTION
Y ELECTROCUTION
Y ELECTROCUTION
Y ELECTROCUTION
Y ELECTROCUTION.....
The electrical installation must be performed by a fully qualified electrician, and in accordance with local electrical
standards and the wiring diagram corresponding to the unit model.
Any modification performed without our prior authorisation may result in the unit’s warranty being declared null and
void.
The power supply cable section must be sufficient to provide the appropriate voltage to the unit’s power supply
terminals, both at start-up and under full load operating conditions.
The power supply cable shall be selected in accordance with the following criteria:
1. Power supply cable length.
2. Maximum unit starting current draw – the cables shall supply the appropriate voltage to the unit terminals
for starting.
3. Power supply cables’ installation mode.
4. Cables’ capacity to transport the total system current draw.
Starting current draw and total current draw are indicated on the unit’s wiring diagram.
Short circuit protection shall be provided. This protection shall comprise fuses or circuit breakers with high breaking
capacity, mounted on the distribution board.
If the local controls includes a remote ambient temperature sensor and/or a set temperature adjustment module, these
shall be connected with shielded cable and shall not pass through the same conduits as the power supply cables as the
voltages induced may create reliability faults in the unit’s operation.
VER
VER
VER
VER
VERY IMPOR
Y IMPOR
Y IMPOR
Y IMPOR
Y IMPORT
TT
TTANT
ANT
ANT
ANT
ANT:::::
3N~400V
3N~400V
3N~400V
3N~400V
3N~400V-50HZ
-50HZ
-50HZ
-50HZ
-50HZ
The outdoor unit is equipped as standard with a phase sequence and cut-out controller located in the electrical box.
THIS PRODUCT IS EQUIPPED WITH A PHASE SEQUENCE CONTROLLER. THE LED’s INDICATE THE FOLLOWING
CONDITIONS:
Green LED =1: low voltage supply
the compressor rotation direction is correct
Green LED =flickering: phase inversion
Green LED =0: phase absent
the compressor and the fans do not start.
