background image

Operational Procedure – Cleaning Windows 

 

49 

Road  Safety

   

Journeys to and from the workplace are subject to documented risk assessment.  
Assessment of these risks will include security of the load to ensure that it does not shift 
under normal driving conditions, emergency braking or during a minor collision. Responsibility 
rests with the driver of the vehicle, however business owners have a responsibility to provide 
suitable vehicles, equipment and means of securing the load.  
 
Consideration should also be given to the potential for the overloading of vehicles fitted with 
water tanks, for when a water tank is full, a vehicle is less likely to be close to its maximum 
payload capacity

.

 To assess road safety risk consideration should be given to: 

   

   The design of the water treatment tanks. 

   The manufacture of the water treatment tanks. 

   The installation of the water treatment tanks. 

   The payload capacity of the vehicle and the potential for overloading. 

   The security of waterfed poles, hose reels and ancillaries etc. 

 
 

Legionnaires  Disease

   

Legionella bacteria can be found in low levels in most water sources, the presence of a few 
bacteria is in itself unlikely to cause a problem, it is when they begin to multiply that the risk 
increases. They require nutrients to multiply, these can be provided by sediment, scale, 
sludge and biofilms. These materials build up in the in the filters used to purify water, if not 
replaced at specified intervals filters may become a fertile breeding ground for Legionella 
bacteria. Water temperature is a particularly important factor in the survival of and 
multiplication of Legionella, when the temperature of water rises above 20° the bacteria begin 
to multiply, the optimum temperature being 37°.

   

   

Contracting the  Disease

   

The disease is normally contracted after the inhalation of the bacterium in small droplets 
(aerosols) or in droplet nuclei that is the residue after the water has evaporated. Waterfed 
poles produce aerosols and it should be noted that aerosols are not restricted to the point of 
production. Under suitable wind conditions, viable bacteria can travel up to 500 meters.

   

   

Legionella will not normally multiply in cold water systems or even hot water systems when 
the water is heated at point of use, or when the system is in regular use. However Legionella 
will multiply when the right conditions exist, these are; 

   

   When sediment, scale, sludge and bio films build up in filters. 

   When water temperatures rise above 20° (68°F) 

   

Measures that should be taken to control the risk of Legionella are; 

   

   Replacement of filters at specified intervals. 

   Following the manufacturers servicing recommendations. 

   Keeping the system stored in a cool place when not in use. 

   If the system cannot be kept in a cool place, drain tank and filters whenever the system is 

to be left standing ideal for more than three days during warm summer months. 

   

The release of Legionella is also subject to the Control of Substances Hazardous To health 
(COSSH) Regulations 2002. 

   

   

   

Summary of Contents for Zero PPB























































Reviews: