background image

Table of Contents

1. Introduction  ............................................................................................................................  4

1.1. Activate Warranty and Data Recovery Service Protection ................................................  4

2. General Information  ................................................................................................................  5

2.1. Warnings and Notices ...................................................................................................  5
2.2. Package Contents  ........................................................................................................  6
2.3. Identifying Parts  ...........................................................................................................  7
2.4. LED Behavior ...............................................................................................................  8

3. Hardware Installation ...............................................................................................................  9

3.1. Tools and Parts for Drive Installation  ..............................................................................  9
3.2. SATA Drive Installation 
..................................................................................................  9
3.3. Connecting the ioSafe 220+  ......................................................................................... 14

4. Install Synology DiskStation Manager ...................................................................................... 15
5. Connect and Log in to Synology DiskStation Manager .............................................................. 17
6. Product Support and Data Recovery Service  ........................................................................... 19

6.1. Activate Data Recovery Service Protection  ................................................................... 19
6.2. ioSafe No-Hassle Warranty  
.......................................................................................... 19
6.3. Data Recovery Procedure 
............................................................................................ 19
6.4. Contact ioSafe Support ................................................................................................ 20

ioSafe 220+ User Manual

3

Summary of Contents for 220+





















Reviews: