background image

 

 

5.9   The machine will not move forwards or backwards. 

- The switch in the driver's seat is broken. 
- Check the fuses 
- Insert the battery plug into the machine socket. 
- Turn key switch. 
- Lock the plug at the red emergency lever  
- Release parking brake. 

 
 

6.   Service and maintenance 

 
6.1 

Before  any  cleaning  or  servicing  work  is  carried  out  on  the  machine  and  before  any  parts  are  replaced,  the 
following precautions must be taken: the machine plug must be removed from the battery socket, the key must 
be removed from the key switch and the parking brake must be applied so the machine cannot move. 

 

When leaving the machine, the operator should apply the parking brake to ensure the machine does not move 
unexpectedly. 

 

IMPORTANT: 

Before  changing  the  main  fuse,  it  is  ESSENTIAL  that  the  battery  cabling  is  disconnected 
from the batteries. 

 

6.2

 

ATTENTION: 

Only valid for Titan 351 BF 140 

 

The level of brake fluid in the brake fluid reservoir behind the driver's seat should be checked regularly once a 
week and topped up if necessary.  The brake fluid should be replaced completely once a year. 

 
IMPORTANT: 

Brake fluid is corrosive and toxic. HANDLE WITH CARE, AVOID SPILLS AND DISPOSE OF 
APPROPRIATELY.  

  
6.3 

The tyres should be examined at regular intervals and any foreign matter such as fragments of metal, splinters 
of broken glass etc should be removed. 

 
6.4 

Check the state of the squeegee blades regularly and turn or replace if worn.  See also 5.4 and 5.5. 

 
6.5 

The filters in the clean water tank should be cleaned regularly at least twice a week. 

 
6.6 

The vacuum motor, water pump and solenoid valve are below the water tank.   The vacuum motor ventilation 
slits must be checked regularly for blockages and cleaned if necessary.  This is especially important when the 
dirt includes large amounts of fluff. 

 
6.7 

The dirty  water tank should be rinsed out regularly  with the drain hose open (to drain the  washing  water), to 
prevent the formation of bacteria.  After finishing cleaning, leave the lid open to allow drying. 

 

IMPORTANT: 

After  each  cleaning  cycle,  the  tank  should  be  raised  and  left  open  in  order  to  avoid 
damage to the lid gasket.   

  
6.8 

If not used for long periods, leave the machine with the battery charged and the battery plug unplugged.  

 
6.9 

A general control by authorised IPC GANSOW personnel is recommended at least once every six months. 

 
6.10  Faulty or unused batteries should be disposed of correctly.  
 
6.11  For more information on our branches and authorised distributors in Germany and other countries, see the list 

of addresses below.  

 
IMPORTANT: 

Rooms where batteries are being charged should always be well ventilated. 

 

 
 
 

Summary of Contents for TITAN 151BF 87











Reviews: