IPC APTA40008, Instruction Manual

English

- 13 -

stability.

- Connect a 5/8 inch ID or larger garden hose to the supply water 

connection fitting. Use of more than 100 ft of garden hose may 

affect system performance.

- Connect the male end of the garden hose to the INLET port 

on the equipment.

- Position the WASTEWATER hose outlet to landscape or other 

area to accept the concentrate water flow. Additional garden 

hoses may be added if required to reach designated area.

- Connect the PURE WATER hose to the fitting on the end, in 

the center of the cap.

- Connect the other end of the PURE WATER hose to the water-

fed pole hose. A control valve is typically installed between these 

two hoses for operator control. (Fig. 2-2A)

Electrical connection (Vers. E).

Warning

The equipment should be connected to the mains in accordance 

with current legislation. 

Make sure the mains voltage corresponds to the voltage 

required by the appliance and indicated on the ratings plate.

Protect the electric cable from accidental crushing.

Failure  to  respect  the  above  conditions  absolves  the 

manufacturer  from  all  liability  and  represents  negligent 

use of the product.

Protection against accidental contact.

Before removing the panels, unplug the appliance from the 

mains. Before using the appliance, make sure the panels are 

correctly assembled and fixed.

Failure to respect  these instructions could result in electric 

shock and absolves the manufacturer from all liability.

RECOMMENDATIONS FOR USE

Cleaning of covered and painted surfaces.

The use of pure water on glued surfaces could cause detach-

ment. Do not use the appliance on parquet or wooden floor that 

are not well sealed.

Pay the utmost attention when cleaning covered and painted 

doors, parquet, aluminium panels and surfaces in general.

Before using pure water, we suggest to test a corner of the 

surface, in order to avoid damage during cleaning.

Window cleaning.

Do not lead the stream of water directly on the sealed area of 

the window, so not to damage the sealed corners.

USING THE EQUIPMENT

Starting the Equipment:

- Turn water supply valve to its full open position.

- Verify water flow at the WASTEWATER outlet.

Equipment with Pump Unit.

- Turn motor switch ON by pressing the push button.

- Allow PURE WATER to flow from brush for 1 - 2 minutes.

- Take a sample of the PURE WATER at the brush and test it 

with the TDS meter. If water test is higher than 10 ppm, service 

of Equipment is required.

- Wash windows as directed. Adhere to safety precautions for 

use as recommended by pole manufacturer.

The leftover water now has higher TDS level than when it ente-

red the system and is called concentrate. It exits the membrane, 

flows around the outside of the DI cartridge and out through 

the side port marked waste water. There is an automatic flow 

regulator installed in the waste water outlet fitting which con-

trols the waste water flow rate to maintain the proper balance 

of the entire system. Concentrate water discharge flow can be 

directed safely to any landscape vegetation, to a sanitary or 

storm sewer drain.

The unit must be protected from freezing.

PRELIMINARY OPERATIONS

Unpacking:

After unpacking the appliance, check it is complete and un-

damaged.

If in doubt, do not use the equipment. Contact your dealer. 

Packaging (bags, boxes, nails etc) should be kept out of reach 

of children as they may represent a potential hazard. They 

should be disposed of or kept according to national environ-

mental legislation.

Assembling parts supplied separately.

All main parts and safety devices are assembled by the 

manufacturer. Some other secondary parts may be supplied 

separately.

These parts must be assembled by the user following the as-

sembly instructions.

The pre-filter, RO membrane and DI resin cartridge are already 

installed inside the Appliance.

Identification plate:

Warning

When purchasing the product, make sure it has an identification 

plate. If this is missing, notify the manufacturer and/or dealer 

immediately.

Use of an appliance without an identification plate absolves the 

manufacturer from all liability. Products without an identifica-

tion plate should be considered as anonymous and potentially 

dangerous.

The main technical characteristics of the equipment are given 

on a plate applied on the back of the appliance.

The user must ensure that the rooms where the equipment is 

to be used comply with all safety standards and regulations 

regarding:

- efficient electrical installations;

-  the  absence  of  explosive,  inflammable,  toxic  or  corrosive 

substances.

Use of the appliance in particular conditions requiring use of 

class II appliances only is not recommended.

Hose assembly

: 

Attach the wastewater discharge hose to the wastewater outlet 

port on the side of the tube near the handle.

The equipment is now ready for use. (Fig. 1)

Water circuit connection and accessories:

- Locate supply water connection at job site.

- Find suitable setup location for appliance at the job site.

- Lay equipment down in a horizontal position for maximum 

!

!