background image

FXO2 

User Guide ver. 1.1 

Autotranslation, no pics 

 

2 SIP, 2xRJ45, 4xRJ11 

Pre-version userguide 

page 13 of 13 

 

© IPshop ApS 2009 

I:\FAQ\FXO2\userguide\FXO2_UG_EN.doc Ver. 1.1 

 

WARNING! When the terminal is updating, never power down the FXO2. It will 
destroy the equipment. 

3.10.2 Change Password 

A

) 

User Password (default:1234) 

User password is for the user of “user”. “user” is the lower level user of the 
configuration, when “user” login, “Call setting” will not show. It means “user” only can 
setup something like network etc. 

B

Administrator Password (default: admin) 

Administrator Password 

is the password of “admin”. ”admin” can change anything of 

FXO2 so please reminded change the password of “admin” after you finish configure 
the device. 

3.10.3 Reset Configuration 

When reset configuration is click FXO2 will reset to factory default. 

After reset all the configured will be lost

3.10.4 Reboot the Device 

Click on this field to reboot the device. 

4 Products Parameter 

Characteristics of the hardware Parameter Remarks 

Processor ARM9E 133MHz 
DSP VDS924PM4 200MHz 
RAM 16M 
FLASH 4M 
Power DC12V/500mA +-10% 
Consumption The maximum 3 W 

Impedance 600 ohm 
Ring Detect Range 30-150Vrms 18Hz-55Hz 
PSTN Port Voltage Upper Limit 160V 

LED Operate, network , circuit 
Network card 2 100/10BASE-T 
Weight 

230 grams 

WHITOUT DC ADAPTER 

Working temperature 0

42

℃ 

Working humidity 40

%-

90

% 

not congealed 

Colour White 
PSTN Ports 2 
VoIP Chunnel 2 

Manufactory Parameter 

Parameter 

Default 

LAN DHCP 
Network 
PC Static IP:192.168.8.1 
admin admin 
Password 
user 1234 

Time Zone GMT

This default parameter are unsuitability the customization’s products.

 

Summary of Contents for FXO2














Reviews: