background image

 

 

Author:  RRi 

Page  -  38  - 

Version  1.0 

Date:  10-2019 

BLANKOM-IPQAM-801_User_Manual_ENv1.0.docx 

 

IPQAM-801 DVB-C A/C Modulator IP to QAM User Manual 

 

decoded pictures at that location in the video stream despite using different pictures, or no pictures at all, as 

references prior to the switch. 

General notes about Streams: 

Multicast Address Ranges: 

We recommend, that the addressing of your Multicast streams should be in conjunction with this listings to avoid 

conflicts with other network equipment or protocols. 

https://www.iana.org/assignments/multicast-addresses/multicast-addresses.xhtml

 

 

One small part from this: 

IPv4 Multicast Address Space Registry 

Last Updated 

2018-01-05 

Expert(s) 

Stig Venaas 

Note 

Host Extensions for IP Multicasting [

RFC1112

] specifies the extensions required of a host 

implementation of the Internet Protocol (IP) to support multicasting.    The multicast addresses are in 
the range 224.0.0.0 through 239.255.255.255. Address assignments are listed below. 
 
The range of addresses between 224.0.0.0 and 224.0.0.255, inclusive, is reserved for the use of 
routing protocols and other low-level topology discovery or maintenance protocols, such as gateway 
discovery and group membership reporting.    Multicast routers should not forward any multicast 
datagram with destination addresses in this range, regardless of its TTL. 
     

Available Formats 

XML

 

 HTML 

  Plain text 

Registries included below 

 

Local Network Control Block (224.0.0.0 - 224.0.0.255 (224.0.0/24))

 

 

Internetwork Control Block (224.0.1.0 - 224.0.1.255 (224.0.1/24))

 

 

AD-HOC Block I (224.0.2.0 - 224.0.255.255)

 

 

RESERVED (224.1.0.0-224.1.255.255 (224.1/16))

 

 

SDP/SAP Block (224.2.0.0-224.2.255.255 (224.2/16))

 

 

AD-HOC Block II (224.3.0.0-224.4.255.255 (224.3/16, 224.4/16))

 

 

RESERVED (224.5.0.0-224.251.255.255 (251 /16s))

 

 

DIS Transient Groups 224.252.0.0-224.255.255.255 (224.252/14))

 

 

RESERVED (225.0.0.0-231.255.255.255 (7 /8s))

 

 

Source-Specific Multicast Block (232.0.0.0-232.255.255.255 (232/8))

 

 

GLOP Block

 

 

AD-HOC Block III (233.252.0.0-233.255.255.255 (233.252/14))

 

 

Unicast-Prefix-based IPv4 Multicast Addresses

 

 

Scoped Multicast Ranges

 

 

Relative Addresses used with Scoped Multicast Addresses

 

Summary of Contents for BLANKOM IPQAM-801
























































Reviews: