IRIS ID IrisAcces ICU7000-2 Hardware Manual Download

Page: 12 / 12

General Information

Technical Support

8.66” x 9.65” x 2.0” (220mm x 245mm x 51mm)

Dimension (W x H x D)

3.0lbs (1.4kg)

Weight

12-24VDC, 2.0 Amps @ 12VDC / 24W

Power Input / Consumption

External Green LED for Power Indication

Indication

32°F ~ 122°F (0°C ~ 50°C)

Operating Temperature

-4°F ~ 203°F (-20°C ~ 95°C)

Storage Temperature

0 ~ 95% Non-condensing

Humidity

Ethernet (LAN, WAN)

Communications

2 Remote Channel (Wiegand In/Out, Dry Contact Relay x 2, Programmable
GPIO x 4, RS422) x 2

Inputs / Outputs

CE, FCC, KCC, UL294

Certifications

Iris ID Systems, Inc.

www.irisid.com

7 Clarke Drive, Cranbury, NJ 08512, USA
Tel. 609-819-IRIS(4747) Fax. 609-819-4736

Printed in Korea

Additional information and technical assistance is available on the Iris ID support web site
at www.irisid.com/supportservices

formerly

Summary of Contents for IrisAcces ICU7000-2













Search results

Summary of Contents for IrisAcces ICU7000-2

Reviews:

Related manuals for IrisAcces ICU7000-2

Brands by name

Popular brands

IRIS ID IrisAcces ICU7000-2, Hardware Manual

Search results

Summary of Contents for IrisAcces ICU7000-2

Reviews:

Related manuals for IrisAcces ICU7000-2

Brands by name

Popular brands