background image

 

19 

Splitting Operation 

 

WARNING 

Before starting this log splitter, review the following instructions and safety information for safe 
operation of the log splitter. 
Failure to follow these rules may result in serious injury to the operator or bystanders from moving 
parts that crush, cut, or entangle from flying objects, burns, fire, falling or tripping, or from carbon 
monoxide poisoning. 

 

General Safety Information: 

 

Read manual.  

Do not allow anyone to operate the log splitter who has not read the Owner's Manual or has not 

been instructed on the safe use of the splitter.

 

 The log splitter owner should instruct all operators in safe log 

splitter operation. 

 

Age restrictions

.  Never allow anyone under 16 years old to operate the log splitter.  Anyone 16 years and older 

must be trained and supervised by a trained adult. 

 

Intended use

.  Log splitters should only be used for splitting wood logs, lengthwise with the grain.  Do not use for 

other purposes as unforeseen hazards may result. 

 

Modifications

.

  

Never modify or alter the log splitter in any way.  Modifications can create serious safety hazards 

and will void the warranty.

 

 

Attachments

.  Never add attachments to the splitter, except for authorized accessories supplied by the 

manufacturer with instructions for safe installation and use.  

 

Engine speed

.  The maximum engine speed is preset at a safe limit.  Never attempt to modify the engine speed 

setting to run at a higher speed. 

 

Fuel/exhaust system

.  NEVER modify or add to the exhaust system, fuel tanks, or fuel lines.  Fire can result. 

 

Remote control

.  NEVER attach a rope, cable, or other remote device to the splitting control. 

 

Splitting wedge

.  NEVER attempt to change the height or speed of the splitting wedge. 

 

Pressure setting.

  NEVER increase the pressure setting of the pump or control valve. 

 

Safety equipment / controls

.  Always operate the log splitter with all safety equipment in place and in good 

working order, and all controls properly adjusted for safe operation. 

 

Know how to stop

.  Be thoroughly familiar with all controls and with the proper use of the equipment.  Know 

how to stop the log splitter and relieve system pressures quickly if needed. 

 

Operating speed

.  Always operate the log splitter at the manufacturer's recommended speed.  The maximum 

speed of the engine pump and wedge are preset within safe limits. 

 

Daylight only

.  Only use the log splitter in daylight so you can see what you are doing. 

 

Smoking / sparks

.  Never smoke while operating the log splitter, and never operate near sources of sparks or 

flames. 

 

Under the influence

.  Never operate, or let anyone else operate, the log splitter while under the influence of 

alcohol, drugs, or medication. 

 

Unattended

.  Never leave the machine unattended while the engine is running. 

 

Refueling

.  Never refuel the engine until it has cooled at least two minutes. 

 

Adjusting / repairing

.  Always make sure the engine is off before cleaning, repairing or adjusting the splitter, 

except as recommended by the manufacturer.   In addition, disconnect the spark plug and move all control handles 
back and forth to relieve system pressure 

before changing or adjusting hydraulic system components

 such as 

hoses, tubing, fittings or other components. 

 

Replace labels

.  Always make sure safety labels are in place and in good condition.  If a safety label is missing or 

not legible, order new labels because unsafe operation can result.  Call 1-800-817-1005 to order new safety labels. 

 

Summary of Contents for BHVH2418GX





















































Reviews: