background image

3. SPECIFICATIONS

4. TERMINALS PURPOSE

Computer Interface: .......................................................................USB 2.0 (CDC/HID)
Max. distance from a PC: .....................................................................................1.8 m.
Consumption current from a USB port: ..............................................................100 mA.
Consumption current with reader attached: ....................................................≤ 450 mA.
Maximum allowed consumption current from a 12 V converter: .........................150 mA.
Supported protocols: ......................................................................... iButton, Wiegand.
Bit width of Wiegand protocol: ...............................................................................Auto.
Casing material: .................................................................................................Plastic.
Dimensions, mm: .......................................................................................64 x 64 x 19.
Gross weight: .......................................................................................................150 g.

Device dimensions are presented in Figure:

64

6

4

19

58

58

5

+12V

Power output for external devices

GND

Ground, power (-)

DAT A 0

iButton DATА0 for W iegand

DAT A 1

iButton DATA1 for W iegand

LED G

Green LED ex ternal c ontrol
by c omm ands from PC

LED R

Red LED external control
by c omm ands from PC

BEEP

Buzzer ex ternal control
by c omm ands from PC

POWER

M12 V output to power
external

devices

by

com mands

from PC

page 2

Z-2 BASE

www.ironlogic.me

Summary of Contents for Z-2 BASE










Reviews: