background image

8

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Appliance Installation, Service, and 

Maintenance Notices

WARNING: Improper installation, adjustment, alteration, 

service or maintenance can cause injury or property damage. 

Refer to the owner’s information manual provided with this 

appliance. For assistance or additional information consult a 

qualified installer, service agency or the gas supplier.

AVERTISSEMENT : Une installation, un réglage, une 

modification, une réparation ou un entretien mal effectué 

peut causer des dommages matériels ou des blessures. 

Voir la notice de l’utilisateur qui accompgne l’appareil. 

Pour de l’aide ou des renseignements supplémentaires, 

consultez un installateur, un technicien agréé ou le 
fournisseur de gaz.

Only trim kit(s) supplied by the manufacturer shall be used 

in the installation of this appliance. 

Seules les trousses de garniture fournies par le fabricant 

doivent être utilisées pour l’installation de cet appareil.

These appliances must not be connected to a chimney or flue 

serving a separate solid fuel burning appliance.

Any change to this appliance and/or its operating controls is 

dangerous. Improper installation or use of this appliance can 

cause serious injury or death from fire, burns, explosion or 

carbon monoxide poisoning.

CARBON MONOXIDE POISONING: Early signs of carbon 

monoxide poisoning are similar to the flu with headaches, 

dizziness and/or nausea. If you have these signs, obtain fresh 

air immediately. Turn off the gas supply to the appliance and 

have it serviced by a qualified professional, as it may not be 

operating correctly. Some people are more affected by carbon 

monoxide than others, including pregnant women, people with 

heart or lung disease or anemia, those under the influence of 

alcohol, and those at high altitudes.

Turn off gas and electrical power to the appliance and allow 

it to cool before cleaning or servicing the appliance.

If the barrier becomes damaged, the barrier shall be 

replaced with the manufacturer’s barrier for this appliance.

Si l'écran est endommagé, il doit être remplacé par 

celui fournit par le fabricant de cet appareil.

Reinstall any barrier removed before operating the 

appliance. The barrier is designed to reduce the risk of 

burns from hot glass. Do not operate the appliance without 

the barrier installed.

Appliance Operation Notices

These fireplace inserts are vented gas appliances. Do not 

burn wood or other material in these appliances.

These appliances are designed to operate on natural gas or 

propane gas only. The use of other fuels or combinations of 

fuels will degrade the performance of this system and may 

be dangerous.

Provide adequate clearances around air openings and 

adequate accessibility clearance for service and proper op-

eration. Never obstruct the front openings of the appliance.

These appliances are designed as supplemental heaters. 

Therefore, it is advisable to have an alternate primary heat 

source when installed in a dwelling.

Warranty Information

Your gas appliance is covered by a limited

 

20-year warranty. 

You will find a copy of the warranty accompanying this manual.  

Please read the warranty to be familiar with its coverage.

Retain this manual. File it with your other documents for 

future reference.

Failure to comply with the installation and operating 

instructions provided will result in an improperly installed 

and operating appliance, voiding its warranty.

Do not attempt to alter or modify the construction of the 

appliance or its components. Any modification or alteration 

may void the warranty, certification, and listings of this unit.

Summary of Contents for Madison Park MPI27









































Reviews: