background image

Important safety instructions

DANGER!

DANGER!

This device is part of a high voltage supplying systems.
High voltages are dangerous and may be fatal.

USE CAUTION WHILE WORKING WITH THIS EQUIPMENT.
BE AWARE OF ELECTRICAL HAZARDS.

Always follow at the minimum these provisions:

High voltages must always be grounded

Do not touch wiring or connectors without securing

Never remove covers or equipment

Always observe humidity conditions

Service must be done by qualified personnel only

WARNING!

WARNING!

To avoid injury of users it is not allowed to open the unit. There are no parts which can be maintained by users 
inside of the unit. Opening the unit will void the warranty.

WARNING!

WARNING!

Before connecting or disconnecting HV cables or any operation on the HV output or the application, the unit has
to be switched off and discharge of residual voltage has to be finished. Depending on application residual 
voltages can be present for long time periods.

WARNING!

WARNING!

Do not operate the unit in wet or damp conditions.

WARNING!

WARNING!

Do not operate the unit in an explosive atmosphere.

WARNING!

WARNING!

Do not operate the unit if you suspect the unit or the connected equipment to be damaged.

ECH 124 / 128 / 12A / 14A - MMC Crate | Last modified on: 24.01.2020 | www.iseg-hv.com

5/20

Summary of Contents for ECH 124





















Reviews: