12.7 Maintenance interval display
If the internal 4-digit program switch is used, a service
interval display will be available. A yellow LED will inform
you about required maintenance work.
12.8 Use in a hold-open system
If the drive is used on a smoke control door or fire door,
the drive will usually be operated in a hold-open system in
combination with smoke detectors. The drive of the door will
keep the door open either permanently (PERMANENT OPEN)
or temporarily (AUTOMATIC). However, in case of a fire,
the door must close in order to prevent smoke and fire from
spreading. For this reason, the opening automatic of the
drive will be automatically shut off as soon as a connected
smoke detector detects smoke; this is indicated on the
smoke detector by a red LED. The door can then only be
opened manually. The hold-open function will be canceled
even if the power supply is interrupted.
Manual activation of the hold-open function
In case of danger, the door can also be closed manually -
either by pushing the optional red pushbutton with the label
"Close door" or by manually moving the door approx. 10-20
cm in the Closed direction.
Recommissioning the drive unit
In order to reestablish the drive function, the hold-open
system must be reset. In accordance with the legal
provisions, this must be carried out manually. The reset can
be carried out in different ways.
Reset via the door position
1.
Reset the smoke detector (LED display is green).
2. Completely close the door.
3. Open the door to the adjusted opening width.
4. Release the door.
Reset via the program switch
1. Reset the smoke detector (LED display is green).
2. Program switch in OFF and back.
Smoke control doors and fire doors are important for
your safety. However, this is only the case if the doors
will properly close in the case of danger. Therefore, do
not use additional wedges or objects that could prevent
the closing.
13. Maintenance and care
Maintenance
Maintenance work must be carried out only with the system
de-ernergized (turn off the fuse protection on site).
Acceptance and regular inspection
As the operator of the automatic door, you are responsible for
the regular inspection of the system. An initial inspection is
required before the initial commissioning. The acceptance must
be carried out according to the inspection book by a person
trained by ISEO. The door system is then to be inspected and
maintained, if necessary, at least once a year by a specialist.
All inspections will be documented in the inspection book (from
page 8 in these operating instructions). It serves as proof that
you have fulfilled your obligations and it must be retained.
Have the door system inspected and maintained, if necessary, at
least once a year by a specialist.
The testing and approval must be carried out according to the
inspection book by a person trained by ISEO.
The results are to be documented and to be retained by the
operator for at least 1 year.
The following parts are wear parts and need to be checked at
least once a year and replaced, if necessary (see installation
instructions) :
• Arm assembly
• Sliding piece
• Slide channel
Use only original spare parts.
Care
Turn the program switch during the cleaning to the OFF
position or PERMANENT OPEN position in order to prevent
unintended movements.
Never let water or other liquids enter the drive
unit.
Never insert a metal object into the openings of the drive
unit. Otherwise, there will be the risk of an electrical shock.
Clean the drive with a moist cloth and common cleaning agents.
Do not use any scrubbing agents as they might damage the
surface.
Do not start the device before the surfaces are dry.
14. Maintenance by ISEO
A regular maintenance of your system will pay off :
weak spots are detected and eliminated early, the service life will
be increased.
ISEO and its authorized partners offers a premium maintenance
service for automatic doors and catching devices, whereby the
offcial seal of approval provides the operators of the building with
reliable safety. If not all door systems are properly tested, the
building operator will be liable for property damage and physical
injuries in case of an accident. Irrespective of safety aspects,
a regular maintenance makes also sense from an economic
point of view. This allows you to detect and eliminate possible
damage or wear early on. The risk of unforeseeable costs due to,
for example, high repair costs can be minimized – and we will
help you keeping an eye on your budget. The goal is always to
increase the service life of your door systems.
ISEO will assume the complete organization and execution of
the maintenance. Your benefits: all installations will be tested
by trained experts in regular intervals - even systems from other
manufacturers. The building operator does not have to take care
of anything; legal requirements will be met in a reliable manner.
A maintenance contract for the door will ensure the tested
reliability according to a premium standard.
IS 9100
—
34 ISEO
