When an Error Message is Displayed
v
Check the error code and error code number displayed on the
operation panel.
.
J a m ( H o p p e r )
9 0
List of Error Codes
v
Click on an error code below to jump to the page with the
corresponding error descriptions.
"44" (
A
page 43) "90" (
A
page 42) "91" (
A
page 42)
"92" (
A
page 42) "93" (
A
page 42) "94" (
A
page 42)
"95" (
A
page 42)
"A1" (
A
page 42) "A2" (
A
page 42) "A8" (
A
page 42)
"AB" (
A
page 43) "AC" (
A
page 43)
"B0" (
A
page 42) "B1" (
A
page 42) "B2" (
A
page 43)
"C1" (
A
page 43) "C2" (
A
page 43) "C3" (
A
page 43)
"D1" (
A
page 42) "D8" (
A
page 43)
"F0" (
A
page 43) "F1" (
A
page 43) "F2" (
A
page 43)
"F3" (
A
page 43) "F4" (
A
page 43) "F5" (
A
page 43)
"F6" (
A
page 43) "F8" (
A
page 43)
No Card
.
v
Cards have run out.
"Replenish the cards." (
A
page 29)
v
The card hopper is not installed.
Install the card hopper.
Memo:
v
The operation panel display appears blinking when the cards have
run out or when the card hopper is not installed.
Jam(Hopper) 90
.
v
Card jam near the card hopper and cleaning roller.
"Remove the jammed card." (
A
page 44)
Jam(TurnOver) 91
.
v
Card jam near the card turn over unit.
"Remove the jammed card." (
A
page 45)
Jam(MG) 92
.
v
Card jam in the magnetic encoder unit.
"Remove the jammed card." (
A
page 47)
Jam(Transfer) 93
.
v
Card jam in the card feed roller.
"Remove the jammed card." (
A
page 48)
Jam(Discharge) 94
.
v
Card jam near the card outlet.
"Remove the jammed card." (
A
page 49)
Jam(Retran.) 95
.
v
Card jam near the retransfer heating roller.
"Remove the jammed card." (
A
page 50)
Film Search A1
.
v
Retransfer film is broken.
"Repair the retransfer film." (
A
page 54)
MG Test Err A8
.
v
A writing error has occurred during magnetic encoder self-diagnosis.
Press
K
N
B
to reset the printer.
Ink Error B0
.
v
An incorrect ink ribbon is installed.
Install a correct ink ribbon.
Ink Search B1
.
v
Ink ribbon is broken.
"Repair the ink ribbon." (
A
page 52)
Door Open D1
.
v
The printer door is open.
Close the printer door, and press
K
N
B
to reset the printer.
v
Cleaning unit is not installed.
Install the cleaning unit, close the printer door, and press
K
N
B
to reset the printer.
Memo:
v
The operation panel display appears blinking when the printer door
is open or when the cleaning unit is not installed.
Film Run Out A2
.
v
Retransfer film has run out.
"Replace with a new one." (
A
page 31)
Troubleshooting
42
Summary of Contents for Peak RTX1000
Page 1: ...Instruction Manual ...
Page 4: ...Warnings Before Use 4 ...
Page 5: ...Caution Before Use 5 ...
Page 18: ... Operating the Printer 18 ...