background image

iSocket

®

 GSM 706/707 

                                                                          

               www.isocket.eu

 

© Copyright Intellectronics 2012 
All rights reserved. Version 1.1.2-EN 

             - 16 - 

         English

 

A  typical  example  of  temperature  control  would  be  heating  activation  in  remote  area  if  the 
temperature drops below 10C (50F). The following settings must be used: THERMOSTAT=HEATING, 

TEMPOFF=10 (or TEMPOFF=50 in Fahrenheit for "US" models), THERMOSTATON. With these settings 

the thermostat will keep the temperature in the range of about 10C (50F). This means that as soon 

as the room is heated up to 10C (50F) the main socket is turned off. If the current temperature in 

the room is over 10C (50F) the main socket does not turn on until the temperature drops below 10C 

(50F). 
 

Another  example  is  air  conditioning  activation  when  the  temperature  exceeds  22C 

(THERMOSTAT=COOLING, TEMPOFF=22, THERMOSTATON). This means that as soon as the room is 

cooled to 22C the main socket is turned off. If current temperature in the room is less than 22C the 

main socket does not turn on until the temperature rises above 22C. TEMPOFF could be installed in 

Fahrenheit for "US" models in that case as well. 

7.3 Temperature Monitoring – Notifications, iSocket

®

 Temperature Notifier 

You  can  receive  a  message  when  the  “switch-off”  temperature  (set  by TEMPOFF=X) is 
reached. This feature is related with thermostat and works only if thermostat is enabled. 
Before setting up such alerts you must set up at least one phone number for alerts. If 

you remove all phone numbers, then alerts will be also disabled (THERMALERT=OFF will 
be active value). 
 

Command 

Description 

Response 

Type 

ALER35
8912345678 

Set the number for SMS. This number is used in 
some other cases - Chapters 9.2, 11 and 12. You 
can install up to 10 numbers. Instructions how 

to add a number are similar to those given in 
Chapter 5.1. You must set up this number before 
doing other configurations! 

ALER3589123
45678 – OK 

30min 

ALERTNUMBER-
3589123456789 

Remove number from list 

ALERTNUMBER -
3589123456789 – OK 

30min 

ALERTNUMBER-ALL 

Remove all numbers 

ALERTNUMBER-ALL – OK  30min 

ALERTNUMBER? 

Information about numbers 

ALERTNUMBERs: 
3589123456789, 
3589223456789 

No ALERTNUMBERs! 

Inf 

THERMALERT=ON 

Enable SMS sending when TEMPOFF is reached 
and main socket is therefore deactivated. 

Works only if thermostat is enabled.

 

THERMALERT=ON – OK 

30min 

THERMALERT=OFF 

Disable SMS alert 

THERMALERT=OFF – OK  30min 

THERMALERT? 

Show current settings for THERMALERT 

THERMALERT=(OFF),ON  Inf 

TRISEALERT=35 

Set the temperature at which you should receive 
a temperature rise alert (the value from -10 to 
50 Celsius, or from 14F to 122F for "US" 

models). 

TRISEALERT=35 – OK 

30min 

TRISEALERT=OFF 

Disable temperature rise alert 

TRISEALERT=OFF – OK 

30min 

TRISEALERT? 

Show current settings for TRISEALERT 

TRISEALERT=30 

Inf 

TFALLALERT=15 

Set the temperature at which you should receive 

a temperature fall alert (the value from -10 to 
50 Celsius, or from 14F to 122F for "US" 

models). 

TFALLALERT=15 – OK 

30min 

TFALLALERT=OFF 

Disable temperature fall alert 

TFALLALERT=OFF – OK 

30min 

TFALLALERT? 

Show current settings for TFALLALERT 

TFALLALERT=5 

Inf 

 

iSocket

®

 Temperature Notifier 

iSocket

®

 Temperature Notifier - this is a feature of the iSocket device which notifies you 

in  the  event  of  the  room  temperature falling  below  or  rising  above  critical levels.  This 
feature does not affect the thermostat and can work independently.  

Summary of Contents for GSM 706





























Reviews: