background image

ENGLISH. The colour version of this document can be found on the website www.isocket.eu 

 
Thank you for choosing iSocket. Please take a few minutes to read through these operating instructions 

carefully  before  using  the  product  so  that  you  can  get  full  advantage  of  the  functionality  and  get 
maximum enjoyment from it. Pay special attention to the safety instructions in Chapter 2! Incorrect use 
could  affect  your  guarantee  or  jeopardise  health  or  property.  We  reserve  the  right  to  make  design 

changes on the device and its software without prior notice. Deviations not mentioned in this instruction 
might exist in the software, which is considered acceptable and not considered a defect. The latest version 

of these instructions can be found on our website www.isocket.eu. Please register as a user if you wish to 
receive  news  from  the  company  (Chapter  20).  Be  sure  to  read  the  terms  of  warranty  before  using  the 
device,  so  that  you  do  not  to  lose  your  rights  under  the  guarantee  as  a  result  of  improper  operation 

(Chapter  19).  You  agree  with  the  terms  of  warranty  and  limitation  of  liability  described  in  Chapter  19 
when you purchase this product. Please keep these operating instructions in a safe place for easy access 
when needed. Intellectronics hope you thoroughly enjoy using your iSocket. 

 

NOTE! 
 

 

These  instructions  apply  to  products  iSocket  GSM  706,  iSocket  GSM  707  and 

iSocket  GSM  706  Light,  iSocket  GSM  707  Light.  In  some  cases  the  text  clearly 
indicates  which  option  is  not  available  in  the  "Light"  version  of  the  product. 
However  please  refer  to  technical  information  (Chapter  17)  for  detailed 
information  about  the  differences  in  the  devices.  The  "Light"  model  does  not 

display  commands  associated  with  optional  features.  The  documentation  and 
product are subject to change without notice. 

 

 

The  software  supplied  with  this  product  is  the  exclusive  property  of 

Intellectronics.  As  an  end-user  you  are  granted  a  non-exclusive  license  to  use 
this software solely in combination with the device on which it is installed and 

with  which  it  is  supplied.  The  license  is  non-transferable  and  you  do  not  have 
the rights to grant sublicenses. 

 

 

Your  iSocket  device  has  a  unique  feature  -  "  iSocket

®

  Online  24/7"  -  that  gets 

the  device  back  online  even  after  a  break  in  the  GSM-network.  However  the 
device  needs  a  strong  GSM  signal  in  the  area  -  it  has  an  internal  antenna  and 
may  not  operate  efficiently  if  the  signal  in  your  area  is  weak.  Ensure  that  you 

have a strong GSM network before using the device. Do not put metal or other 
conductive objects near the device - this may cause signal loss. This product is 
designed for home and office use only. 

 

 

Different types of alerts that iSocket send you (power failure / power restored / 

temperature rise /temperature fall / sensor triggered / etc.)  rely on the correct 
configuration  of  the  mobile  phone  number  for  the  alerts.  Please  follow  the 

instructions  in  section  7.3  where  you will  find an introduction  to  the  command 
ALERTNUMBER which will enable you to configure this number. 

 

 

The "707" model uses a Lithium-ion battery and MUST NOT be used outside the 

specified  temperature!  Please  refer  to  technical  information  (Chapter  17)  for 
detailed information about operating conditions and read the safety instruction 
(Chapter 2) carefully.  

 

 

If you wish to use the iSocket Power Notifier feature, plug in the device for 10 

hours before use. This will charge the built-in battery. 

 

 

If you use a prepaid card you might be need to activate it first with your cell 

phone network provider. More information is available from 

www.isocket.eu/prepaid/ 
 

Summary of Contents for GSM 706





























Reviews: