ISOFIX AY-i122-ISOFIX, Instruction Manual

28

29

4. InsTallInG THe IsoFIX Base

1.  Place the child seat on the car seat. Hold the safety seat with both hands and insert 

the two Isoclick Fix arms 

(o)

 firmly into the vehicle´s isofix anchoring points

 until 

they fasten with a click on both sides. the red button 

(P) 

will change to green on 

both sides (fig. 4 .1).

2.  shake the isofix base to check is properly anchored.
3. Push the Isofix base against the car seat to check that the IsoFIX system is fully 

latched, ensuring that the child seat is as close to the car seat as possible (fig. 4.2).

4. Press the support leg adjuster button 

(r)

 (fig. 4.3) and extend the leg until 

it makes full and firm contact with the floor of your vehicle (fig. 4.4). Green 

connection indicators will appear, indicating that the base has been installed 

correctly (fig. 4.5).

5. InsTallInG THe cHIld seaT rearWard FacInG. GrouP 0 and 1

Only for use with Group 0and 1. From 

approx. 0 to 4 years of age (0-18 kg)

noTIFIcaTIon

1.  line up the green points of the seat with the green points of the isofix base and 

install the seat on the anchoring points 

(W)

 facing away from the direction of travel 

(fig.5.1 and 5.3).

2. make sure that the seat is in recline position 4. If not, pull the recline lever to adjust 

the seat until it is in this position (fig. 5.2).

3. Press the red button 

“press” 

(V)

 situated on the front of the base, which will 

push the button 

“push” outward to close and lock the anchoring points. the red 

“press” button will remain protruding, displaying the green “lock” indicator, which 

indicates that the anchoring points are securely fastened (fig. 5.4).

4. shake the seat to check that it is properly anchored

.

6. FasTenInG THe cHIld InTo THe seaT. GrouP 0 and 1

the correct adjustment of the headrest ensures that the child is properly fastened 

into the car seat. the headrest must be adjusted so that the harness (which moves 

with the headrest) is at shoulder height on the child or slightly above, but never 

behind the back or at ear level  (fig. 6.2).
1.  Put your hand on the headrest and push the lever upwards  

(a)

 while holding 

the seat down with your other hand to prevent it from moving (fig. 6.1). adjust 

the headrest on the right shoulder height for the child.

2. Press the harness adjustment button 

(I)

on the front part of the seat while 

simultaneously pulling both harness straps towards you to loosen it (6.3).

3. open the harness buckle by pressing the red button on the buckle (fig. 6.4) and 

put the the harness on both sides of the seat.

4. sit the child on the seat and fit the safety harness around the child.
5. Put together the 2 parts of the fastener (fig. 6.5).
6. connect the 2 parts of the fastener, inserting them into the buckle until you 

hear a click (fig. 6.6) which indicates that it is securely locked..

7. Pull the harness adjustment strap 

(J)

until the harness is fully tightened (fig. 6.7). 

8. Remember that in order to guarantee the child’s safety, harnesses must be well-

tightened. (fig. 6.8)

9. make sure the belts are not twisted.

7.  InsTallInG THe cHIld seaT ForWard FacInG. GrouP 1

Only for use with Group 1. From approx. 9 

months to 12 years of age (9-18 kg)

noTIFIcaTIon

For group 1 t

his car seat has 2 modes of installation. although we advise to use 

the seat backward facing to the travel direction for an up to 13 kg child, it is 

possible to install the seat forward facing, if:

•  The size of the vehicle does not allow safe installation of the seat backward facing.
•  The size of the child exceeds the height percentiles and this causes the child to be 

incorrectly positioned in the seat. 

1.  remove the rebound bar 

(M)

 from the isofix base by pressing the rebound bar 

unlocking button 

(n)

.