1
ENGLISH
ENGLISH
Size 35 is not equipped with lubrication channels, the FOR-LIFE system
is applied.
From a technical point of view, the best solution to obtain maximum bearing
life time is to periodically re-lubricate with original grease in the recommended
quantities and interval times. Remember that excessive lubrication can result
in temperature increases and early aging of the grease.
Indicatively, the recommended relubrication times can be obtained from the
data sheet of the vibrator, supplied on request.
The proposed re-lubrication interval times are only indicative, results
from theoretical calculations under specific medium conditions and are
not said to be suitable for any type of application, as there are several
variables to be considered.
Italvibras is therefore available to provide recommendations on the
best lubrication for each type of application.
WARNING: During the first relubrication, introduce a quantity of grease
greater than 20% compared to that indicated, so that the lubrication
channels can also be filled.
It is advised to contact ITALVIBRAS for particular uses which is at
complete disposal to advise the client on the best lubrication possible
for the specific use.
Failure to use original grease type shall void the guarantee with which
the vibrator is covered. Use of a different grease could damage the
electric vibrator.
Never mix greases even if they have similar features. Excessive quantity
of grease causes increased heating of the bearings and consequent
anomalous current absorption.
Respect the ecological laws in force in the country in which the equip-
ment is used, relative to use and disposal of products used for cleaning
and maintenance of the vibrator. Always comply with recommendations
of the manufacturer of these products.
If the machine must be demolished, comply with the antipollution
regulations envisioned in the country of use.
Remember that the Manufacturer is always available for any type of
assistance and spare parts.
5.2 SPARE PARTS
On requesting spare parts always state:
- Type of vibrator
(TYPE detectable from the identification plate)
.
- Serial number
(SERIAL NO. detectable from plate)
.
- Power supply voltage and frequency
(VOLT and HZ detectable from
the identification plate)
.
- Spare part number
(detectable from the spare part table)
and desired
quantity.
- Exact destination address of the goods and means of delivery.
ITALVIBRAS declines any liability for incorrect forwarding due to
incomplete or confused requests.
It’s ITALVIBRAS option to decide to DON’T supply some spare parts if
these parts are involved in not admitted operations.
ITALVIBRAS declines any liability for maintenance operations carried
out by a third part company, even by using original spare parts.
SECTION 6 –
Disposal
ITALVIBRAS is active in research to make its products safer from an envi-
ronmental point of view.
The following basic indications must be considered as recommendations
so that recycling of the vibrator at the end of its life takes place with respect
for the environment.
Always comply with the laws and regulations of the country in which
the disposal takes place.
At the end of its useful life, the product must be collected separately
and not disposed of together with other mixed municipal waste.
For better recycling of the materials belonging to the vibrator, we recommend
disassembling it. The materials deriving from the various parts such as copper,
aluminum, steel, etc. must be separated and disposed of in accordance with
the laws and regulations in force.
Summary of Contents for CDX IMX VMX Series
