background image

1.1

General Safety Notes.

1.2

The operator of the machine is responsible for, and has a duty of care in making sure 
that the machine is operated safely and in accordance with the instructions in this user 
manual. Keep the manual safe and pass it on if the machine is loaned or sold to another
user.

1.3

Please note the following safety points.

1.4

The machine should never be left it in a condition which would allow an untrained or 
unauthorised person/s to operate this machine.

1.5

All due care and diligence should be taken by the operator for the safety of and with
regard to those around whilst using the machine.

1.6

Some or all of the following - warning signs, symbols and/or PPE pictograms may
appear throughout this manual. You

MUST

adhere to their warnings. Failure to doso

may result in personal injury to yourself or those around you.

DANGER

Indicates a hazard, which, if not avoided, could result in serious injury or death.

WARNING

Indicates a hazard, which, if not avoided, could result in serious injury.

CAUTION

Indicates a hazard which, if not avoided, might result in minor or moderate injury.

1.7

READ and keep the manual safe and pass it on if the machine is loaned or sold to
another user.

1.8

You MUST fully understand all instructions to ensure you use and operate the
machine safely.

1.9

Appropriate Personal Protective Equipment (PPE), 

MUST

be worn at all times when

operating or repairing the machine.

1

Summary of Contents for SL-S400



















Reviews: