ITech IT8500plus Series Manual Download

Page: 6 / 29

2BH

Enquire CC mode current value

2CH

Set CV mode voltage value

2DH

Enquire CV mode voltage value

2EH

Set CW mode watt value

2FH

Enquire CW mode watt value

30H

Set CR mode resistance value

31H

Enquire CR mode resistance value

32H

Set CC mode transient current and timer parameter.

33H

Enquire CC mode transient parameter

34H

Set CV mode transient voltage and timer parameter.

35H

Enquire CV mode transient parameter

36H

Set CW mode transient watt and timer parameter

37H

Enquire CW mode transient parameter

38H

Set CR mode transient resistance and timer parameter

39H

Enquire CR mode transient parameter

3AH

Set the list operation mode (CC )

3BH

Enquire the list operation mode.

3CH

Set the list repeat mode (ONCE / REPEAT)

3DH

Enquire the list repeat mode.

3EH

Set list steps counts.

3FH

Enquire list steps counts

40H

Set

one of the step’s current and time values.

41H

Enquire

one of the step’s current and time values.

4CH

Save list file in appointed area.

4DH

Recall the list file from the appointed area.

50H

Set timer value of FOR LOAD ON

51H

Enquire timer value of FOR LOAD ON

52H

Disable/Enable timer of FOR LOAD ON

53H

Enquire timer state of FOR LOAD ON

54H

Set communication address

55H

Enable/Disable LOCAL control button.

56H

Enable/Disable remote sense mode.

57H

Enquire the state of remote sense mode.

58H

Set trigger source.

59H

Enquire trigger source.

5AH

Sending a trigger signal to trigging the electronic load.

5BH

Saving

user’s setting value in appointed memory area for recall.

5CH

Recall

user’s setting value in appointed memory area.

5DH

Set function mode(FIXED/SHORT/TRAN/LIST/BATTERY).

5EH

Enquire function mode state.

5FH

enquire input voltage, current, power and relative state

01H

Get the information of E-Load(rated current/voltage,min voltage,max power,max

resistance,min resistance)

02H

Set hardware OPP point

Summary of Contents for IT8500plus Series





























Search results

Summary of Contents for IT8500plus Series

Reviews:

Related manuals for IT8500plus Series

Brands by name

Popular brands

ITech IT8500plus Series, Manual

Search results

Summary of Contents for IT8500plus Series

Reviews:

Related manuals for IT8500plus Series

Brands by name

Popular brands