background image

PETROL GENERATOR GT SERIES OPERATOR’S 

MANUAL

TRADE SERIES

OPERATION

NEVER exceed the rated wattage capacity of your generator. OVERLOADING may cause SERIOUS 
DAMAGE to the generator and attached electrical devices and may result in fire.

WARNING

!

!

Your generator MUST BE SIZED PROPERLY to provide both the running and starting (surge) wattage 
of the devices you will be powering. Before using your generator, determine the running and starting 
wattage requirements of all the electrical devices you will be powering simultaneously. Following below 4 
simple steps and example on the right:

Step 1. Determine the tools and appliances you want to power at the 
same time
Step 2. List the start up and running power usage (Watts) for each
product
Step 3. Add the total power usage and add 10% as a safety net
Step 4. Choose a generator with a rated and maximum power that equals or exceeds your totals. In 
this case a generator with a rated power of at least 3108W and a maximum power output greater than 
7233W would be required.

STARTING POWER CONSUMPTION

Electronic appliances and brushed motors generally will not draw more than running Watts at start up. 
Induction motors in equipment like air conditioners, welders, water pumps and compressors can draw 
2 to 5 times their running power to start. Please consult your equipment’s rating label, manual or the 
manufacturer to confirm specific requirement. If only the running wattage is given on the nameplate for 
a device with an electric motor, the starting wattage can be approximated to be three to five times the 
running wattage. Estimates for the running wattage requirements for common devices are listed in the 
table below. Guidance for starting wattages is provided in the table’s footnotes. To size your generator 
correctly you need to use Watts - here are some useful calculations: 
Watts = Volts x Amps Example 240 Volts x 5 Amps = 1200 Watts

(a) Hard-starting motors require 3-5 times the rated running watts (b) For extremely hard to start loads such as air conditioners and 
air compressors, consult the equipment dealer to determine max wattage.

DEVICE

RUNNING 

WATTS

DEVICE

RUNNING 

WATTS

DEVICE

RUNNING 

WATTS

Air conditioner (12.000 
BTU)

1700 (a,b)

Freezer

800 (b)

Oven

4500

Battery charger (20 Amp)

500

Hair dryer

1200

Paint sprayer, Airless (1/3 
HP)

600 (a)

Belt sander (3”)

1000

Hand drill (1”)

1100

Paint sprayer, Airless 
(handheld)

150

Chain saw

1200

Hand drill (3/8”)

500

Radio

200

Circular saw(6½”)

2000 (a,b)

Hedge trimmer

450

Refrigerator

600 (b)

Coffee maker

1800 (a,b)

Home computer

150

Slow cooker

200

Compressor (1 HP)

1400 (a,b)

Kettle

2400

Submersible pump (1-1/2 HP)

2800 (a)

Compressor (3/4 HP)

1800 (a)

Jet pump

800 (a)

Submersible pump (1 HP)

2000 (a)

Compressor (1/2 HP)

1400 (a)

Lawn mower

1200

Submersible pump (1/2 HP)

1500 (a)

Curling iron

700

Light bulb (100 Watt)

100

Sump pump

600 (a)

Dishwasher

1200

Microwave oven

700

Television

500

Edge trimmer

500

Milk cooler

1100 (a)

Toaster

1000

Electric nail gun

1200

Oil burner on furnace

300

Vacuum cleaner

250

Electric range (1 element)

1500

Oil-red space heater (140,000 Btu)

400

Water heater

3000

Electric skillet

1250

Oil-red space heater (85,000 Btu)

225

Furnace fan (1/3 HP)

1200 (a)

Oil-red space heater (30,000 Btu)

150

17

www.itmtools.com.au

Summary of Contents for GT Seris



























Reviews: