PS200 Programming & Operation Guide
APPENDIX A-5 QUICK REFERENCE INSTALLATION DRAWINGS
Page 148
PS200 - Multipump Wiring Transmitter Wiring- ACS 800
Synchronous - Multi-Controller - Backup
PT
-
+
Pump 1
(Master)
Drive 2
Drive 3
Drive 4
Pump 1
PT
-
+
PT
+
-
PT
-
+
Loop Powered Instrument Shown
Pump 4
Pump 2
Pump 3
TX ALL DRIVES
Transmitter on each drive/pump
NOTES
In this configuration, each PumpSmart drive is wired with a process transmitter ( pressure
only)
y
Parameter 22.13 must be set to TX ALL DRIVES
y
Communication connections must be made between drives.
Consideration(s)
y
If one drive is powered off, each other drive will continue to receive the process signal
TX ONE MASTER
One transmitter signal shared via Fiber Optic cables
Externally Powered Transmitter
Pump 1
(Master)
Drive 2
Drive 3
Drive 4
-
T
+
NOTES
In this configuration, a single process transmitter signal is shared with the other
PumpSmart drives using the communication connections.
y
Parameter 22.13 must be set to TX ONE MASTER
y
Communication connections must be made between drives.
Consideration(s)
y
If one PumpSmart drive loses power, the signal will Not be transmitted through to
the other drives.
y
If the transmitter is loop powered by PumpSmart, the signal will cease if the power to
the PumpSmart unit is turned off.
PumpSmart Powered Transmitter
Pump 1
Pump 4
Pump 2
Pump 3
Externally Powered Transmitter
-
T
Pump 1
(Master)
Drive 2
Drive 3
Drive 4
+
TX ONE AI
One transmitter shared between all drives
PumpSmart Powered Transmitter
NOTES
In this configuration, a single process transmitter signal is wired in series with all the
PumpSmart drives.
y
Parameter 22.13 must be set to TX ONE AI
y
Communication connections must be made between drives.
Consideration(s)
y
If one PumpSmart drive loses power, the signal will still be transmitted through to
the other drives.
y
If the transmitter is loop powered by PumpSmart, the signal will cease if the power to
the PumpSmart unit is turned off.
Pump 1
Pump 4
Pump 2
Pump 3
Copyright 2003 ITT Industries
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X23
24VDC
1
GND
2
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
-
T
Pump 1
(Master)
Pump 2
(Slave)
Pump 3
(Slave)
Pump 4
(Slave)
+
Power Source
(Any Drive)
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X23
24VDC
1
GND
2
Pump 1
(Master)
Power Source
(Master)
-
T
+
X23
24VDC
1
GND
2
X21
AI2+
5
AI2-
6
Pump 2
(Slave)
Pump 3
(Slave)
Pump 4
(Slave)
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
X21
AI2+
5
AI2-
6
B05029A
SHEET 1 OF 1
REV
0
Issue
-
PS 200 ACS 800 Multipump
Transmitter Wiring V4.0
Drawing is not to scale
Dimensions in inches [mm]
Checked: Tony Stavale
Drawn: AI 060204
Copyright 2004 ITT Industries
Summary of Contents for PumpSmart PS200
