background image

 

 

ENGLISH 

 

 
In case of refrigerant leakage: 
 

-

 

Do not generate flames close to the appliance. 

-

 

Do not switch on/off or plug in/off the appliance. 

-

 

To ventilate immediately the area where appliance is located by opening doors and/or windows. 

-

 

To call to an authorized technical service. 

2.

 

RECEIVING THE MACHINE 

Inspect the outside packing. In case of damages, MAKE THE CORRESPONDING CLAIM TO THE CARRIER. 
 
To confirm the existence of damages, UNPACK THE MACHINE IN THE PRESENCE OF THE CARRIER and state any damage on 
the equipment on the reception document, or on a separate instrument. As from May 1, 1998 complies with the European regulations 
on management of pac

king and packing waste, inserting the “

Green Dot Label

” on all their packages.  

Always state the machine number and model. This number is printed on three locations: 

2.1.- PACKAGING  

There is an exterior label with the manufacturing number. (Figure I) 

2.2.- EXTERIOR OF THE EQUIPMENT 

Located on the back of the unit, the same label as before. 

2.3.- DETAILS PLATE 

Located on the back of the machine. 

(

Figure

 II)

 

Check that the installation kit with the machine includes: 

-Manual. 

- Warranty label indicating serial number. 

 

 

CAUTION:    ALL  PACKING  ELEMENTS  (plastic  bags,  carton  boxes  and  wood  pallets) 
SHOULD BE KEPT OUTSIDE THE REACH OF CHILDREN, AS THEY ARE A SOURCE OF 
POTENTIAL HAZARD 

 
 
 

Figure

 II

 

Figure

 I

 

Summary of Contents for - IQN NUGGETS













Reviews: