ITV NDC-F18 Installation Manual Download | Manualshive

Page: 3 / 24

background image

http://www.itvsystems.com.ua

Integrated Technical Vision Ltd

3

This manual covers installation, programming and utilization of NDC-F18 access
control panel. Read this manual carefully prior to installing and programming the unit.

Design Change Disclaimer

Due to design changes and product improvements, information in this manual is
subject to change without notice. ITV reserves the right to change product
design any time, which may subsequently affect the contents of this manual.
ITV assumes no responsibility for any errors that may appear in this manual. ITV
will make every reasonable effort to ensure that this Installation/Programming
Manual is up to date and corresponds with your shipped unit.

Reproduction Disclaimer

All rights on this document are preserved by Integrated Technical Vision Ltd.
Copying, printing and any other kind of reproduction of the document or its part
without permission of Integrated Technical Vision Ltd. is prohibited.

Trademarks

ITV® is a registered trademark of Integrated Technical Vision Ltd.

Training and technical support

Integrated Technical Vision Ltd. performs training on the installation, programming
and utilization of NDC-F18 access control panel. For additional information about
training and discussing of your particular requirements to the unit please contact
our personnel by the phone numbers below.
It is recommended to pass the training in Integrated Technical Vision Ltd. to person-
nel intended for sales and installation of NDC-F18 access control panel on perma-
nent basis. Technical support for all products of Integrated Technical Vision Ltd. can
be obtained at business time by the phones below:
+380 (0) 44 248 65 88
+380 (0) 44 248 65 89
+380 (0) 44 248 65 90
This support assumes the calls of trained specialists. End users must apply to
their dealers or installers before calling us.
This information is available on our web site www.itvsystems.com.ua

«
1
2
3
4
5
...
»

Summary of Contents for NDC-F18

























Reviews:

No comments

Related manuals for NDC-F18

ACS850-04 series

Brand: ABB Pages: 296

Brand: ABB Pages: 320

Brand: ABB Pages: 50

Brand: ABB Pages: 56

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: IBM Pages: 12

Brand: K&K Pages: 10

Brand: Dantherm Pages: 96

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

Brand: DayTronic Pages: 22

Brand: DayTronic Pages: 414

Brand: Taie Pages: 28

Brand: Zeagle Pages: 37

Brand: Lamtec Pages: 136

Brand: TCS Pages: 16

Brand: Yoshitake Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands