IV Produkt IVC3 Basic Manual Download

Page: 11 / 18

IV Produkt Control Unit IVC3

IVC3 Basic Manual 2004-12-15.doc

11/18

Fan speeds are reduced from forced to normal if outdoors temperature drops below set limit (Outd.

Temp. fan). Fan speed returns to forced when outdoors temperature exceeds limit with more than 2°.

At climate adapted control fan speed sets linear from forced to normal out of set value (Outd. Temp.

fan forced and Outd. Temp. fan normal).

Settings

Setting

Description

Outd. Temp. fan

Normal:

-30 - +30

Fan speed limits to normal speed at outdoor temp. below

set value.

(Climate dep. vent., se chapter 2.8.4)

2.13 Outdoor compensated setpoint

IVC3 are configurable for outdoor temperature compensation of set point. Summer and/or winter

compensation are available. Two limits for outdoor temperature and a compensation value for each

summer and winter can be set.

Settings

Setting

Description

Outd comp summer

Temp 1

-30 - +30

Setpoint for start of summer compensation (at this point

there is no compensation)

Outd comp summer

Temp 2

-30 - +30

Setpoint for full summer compensation (at this point

compensation has is full influence on temp. control)

Outd comp summer

Comp

-30 - +30

The value that compensation would achieve at “Temp 2”

summer.

Outd comp winter

Temp 1

-30 - +30

Setpoint for full winter compensation (at this point

compensation has is full influence on temp. control)

Outd comp winter

Temp 2

-30 - +30

Setpoint for start of winter compensation (at this point there

is no compensation)

Outd comp winter

Comp

-30 - +30

The value that compensation would achieve at “Temp 1”

winter.

2.14 Extended operating time

Extended operating time initiates by an external switch via digital input (activated by a closing contact).

At extended operating time the unit runs with fans in forced speed

When external switch is turned off (open contact) the unit return to operate according to internal time

schedule.

Outdoortemp. (ºC)

Outdoor compensation

Outd. comp summer

Temp 1

Outd. comp summer

Temp 2

Outd. comp winter

Temp 1

Outd. comp winter

Temp 2

Outd. comp summer

comp.

Outd. comp winter

comp.

Setpoint displacement (ºC)

Summary of Contents for IVC3



















Search results

Summary of Contents for IVC3

Reviews:

Related manuals for IVC3

Brands by name

Popular brands

IV Produkt IVC3, Basic Manual

Search results

Summary of Contents for IVC3

Reviews:

Related manuals for IVC3

Brands by name

Popular brands