IV Produkt IVC3 Basic Manual Download

Page: 8 / 18

IV Produkt Control Unit IVC3

IVC3 Basic Manual 2004-12-15.doc

8/18

Fan speed is linear reduced from forced to normal when outdoor temperature decreases from “Outd.

Temp. fan forced” to “Outd. Temp. fan normal”.

Fans will gain forced speed immediately at cooling sequence even if climate controller hasn’t achieved

forced speed.

By input for external timer the fans will run on forced speed.

Settings

Setting

Description

Outd. Temp. fan

normal

-30 - +30

See fig. above

Outd. Temp. fan

forced

-30 - +30

See fig. above

2.9 Control sequence

Cooler, heat recovery (VVX) and heater will in sequence control the temperature. At warming demand

the output to cooler decreases, than VVX starts (with different run/stop intervals out of needs at digital

VVX or with an increasing output signal at analogue VVX) and finally increased output signal to

heater.

The sequence is opposite at cooling request.

Output SA, EA (V)

Outdoor (ºC)

Climate adapted control

Outd. Temp fan

normal

Outd. Temp. fan

forced

Normal

forced

Extract air control

Supply air control

Hysteresis 2º

Output signal (V)

HEATER

VVX

Recovery

COOLER

Set point

supply

Dead zon

2ºC

Supply temp. (ºC)

Sequences

Summary of Contents for IVC3



















Search results

Summary of Contents for IVC3

Reviews:

Related manuals for IVC3

Brands by name

Popular brands

IV Produkt IVC3, Basic Manual

Search results

Summary of Contents for IVC3

Reviews:

Related manuals for IVC3

Brands by name

Popular brands