background image

 

 

 
 
 
 
 

 

 

 

- 4 - 

 

 

 

 

B. Cleaning the Lens 

The Network Camera with Pan/Tilt/Zoom is a network camera with high quality lens. When it is 

necessary to clean the lens, please follow these instructions: 

Prepare cotton swabs and alcohol. 

Moisten the cotton swab with alcohol. 

Slightly clean the lens. 

1. 

If the lens is still dirty, repeat 2~3 steps until it is cleaned. Change a clean cotton swab if 

the old one is dirty or contains dirt that might scrape the lens. 

Never touch the lens hard or 

roughly

C. Technical Specifications 

- Networking 

Protocol 

TCP/IP,  HTTP, SMTP, FTP, Telnet,  NTP, DNS  UPnP, 
DDNS and DHCP 

Physical 

10BaseT Ethernet or 100BaseT Fast Ethernet 
 

 
- Video 

Algorithm supported 

MPEG4 SP 
MJPEG 

Resolution

 

Up to 30/25 frames at 176x120 or 176x144 
Up to 30/25 frames at 352x240 or 352x288 
Up to 15/12 frames at 704x480 or 704x576

 

 
 
- Camera specification 

1/4 inch color CCD sensor 
Typical: 1.5 Lux / F1.8 
Low lux mode: 0.05 Lux/F1.8 
AGC, AWB 
Electronic shutter: 1/60(1/50) to 1/120,000 sec 
Pixel  Numbers:  NTSC  -  542(H)x496(V)  or  PAL  - 
542(H)x586(V) 
 

- Lens 

Focal length 4.2~42mm 

Aperture F1.8~2.9 

10X optical zoom 

10X digital zoom 
 

- General I/O 

1 sensor input(max. 12VDC 50mA) 
1 relay output(max. 24VDC 1A, 125VAC 0.5A) 
 

- LED indicator 

Dual color system status indicator 

 
- Weight 

NET. 450g 

 
- Dimension 

104.5mm(L) * 104.5mm(W) * 127mm(H)

 

 
- Power 

Consumption: MAX 12 W 
Universal switching power-supply included 
Adapter input: 100-240VAC, 50/60Hz, 0.4A 
Adapter output: 12VDC, 1.5A 

 
- Operating Environment 

Temperature: 0-40

°

C/32-104

°

Humidity: 85%RH 

 
-EMI & Safety 

CE, FCC

 

 

 

Summary of Contents for PTZ-3300-01







Reviews: