background image

Specifications

Input channels 1-4:    Transformer, balanced and isolated.  Switchable between microphone or

line input levels.  Microphone input impedance:  1200 

.   Compatible

with microphone sources of 600

 or less.  Line input impedance: 30k 

.

Low cut filter: ----------  6dB/octave, -3dB @ 100Hz
Noise: ------------------- (EIN 20Hz to 20kHz)  -125dBV (200

 source)

Sensitivity: -------------- 0.4mv in for +18dBm out
Input Overload: --------- -9dBV (with 14 dB pad enabled).
Phantom power : ------- +15Vdc

Auxiliary Inputs:
Input impedance: ------- 20k 

Input level: -------------- -10dBV recommended

Outputs: --------------- Balanced, transformer isolated.
Output impedance: ----- 110 

 

Recommended Load Z: 600 

 or greater.

Output level: ------------ +18dBm

Size: --------------------- 19” W x 1 3/4” H X 8 1/4” D (48.3 cm x 4.5 cm x  21 cm)
Weight: ----------------- 10 Pounds with external power supply
Shipping Weight: -----

13 Pounds

Index

Audio Net™ Terminals ------------------------------------------------------------------------------- page 4
Automatic/Manual Switch ---------------------------------------------------------------------------- page 3
Aux Output Level --------------------------------------------------------------------------------------page 3
DC Pwr In ----------------------------------------------------------------------------------------------page 5
Four Automatic Mic/Line Inputs ---------------------------------------------------------------------page 1
Front Panel Controls ---------------------------------------------------------------------------------- page 4
Ground Link Terminals -------------------------------------------------------------------------------page 5
Input Connections Channels 1 - 4 ------------------------------------------------------------------- page 3
Input Switches for Channels 1-4 (Phantom Power, 14dB Pad, High Pass 
                                                     Filter, Aux 1 to Aux Out, Last On) --------------------pages 1 & 2
Internal Controls ---------------------------------------------------------------------------------------page 1
Introduction -------------------------------------------------------------------------------------------- page 1
Line Level Inputs -------------------------------------------------------------------------------------- page 3
Lock LED -----------------------------------------------------------------------------------------------page 2
Microphone Level Inputs ----------------------------------------------------------------------------- page 3
Non-automatic Inputs --------------------------------------------------------------------------------- page 1
Rear Panel Connections ------------------------------------------------------------------------------ page 3
Rear Panel Controls ----------------------------------------------------------------------------------- page 1
Setting Up the Mixer ---------------------------------------------------------------------------------- page 5
Specifications ------------------------------------------------------------------------------------------ page 6
The Two Aux Inputs, and the Main and Aux Output --------------------------------------------- page 3

Summary of Contents for 802A









Reviews: