15
Instruction manual
EN
Saw blade Installation
Pull the plug of power cord out of socket.
1.
Clear all the cutting chips in the saw blade.
2.
Open the lower guard (8) by using the lower guard lifting
3.
rod (10).
Install the saw blade conforming to figure.
4.
[F3]
WARNING
Make sure that the arrow in the saw blade is in the same
direction guided by the arrow of the upper guard (6) of the
saw blade.
Install the outer flange (14) properly.
5.
Insert the hex bolt (13).
6.
Press the spindle lock (5) to prevent the rotation of the saw
7.
blade.
Screw up the hex bolt (13) with hexagon wrench (15), and
8.
put it back after operation.
Install the blade in the correct rotation direction, do not install it
in reverse direction, or serious damage to the blade may occur.
[F4]
Maintenance and storage
CAUTION
Before any work on the machine itself, pull the mains plug.
Always keep the tool and the ventilation slots (if present)
•
cleaned. Regular cleaning and maintenance of the appliance
will ensure efficiency and prolong the life of your tool.
If the tool should fail despite the rigorous manufacturing
•
and testing procedures, the repair should be carried out by an
authorized IVT customer service.
Keep all nuts, bolts, and screws tight, to be sure the tool is in
•
safe working condition.
Replace worn or damaged parts for safety.
•
Use only original spare parts. Parts not produced by
•
manufacturer may cause poor fit and possible injury.
Store the tool in a dry room out of reach of kids and away
•
from any flammable material.
Never wet the device or spray water on it!
•
Remove the blade and clean the motor flange, the flange
•
nut and the protective guard after finishing work.
Carefully check the blade for signs of damage such as
•
broken segments etc. Continued use of a worn or damaged
cutting blade will result in reducing cutting efficiency and may
seriously overload the motor. Damaged cutting blades must be
replaced immediately.
Cleaning the multi purpose cutter
Pull the plug of power cord out of socket.
1.
Wipe the multi purpose cutter with a dry and soft cloth. Do
2.
not clean it with wet cloth or detergent, or the surface coating
of the metal cutting machine will be damaged.
Pay attention to wipe off the grease on the machine, or the
3.
machine will become slippery and hard to hold.
Remove the saw blade and wipe off dust on it.
4.
Environmental protection
Recycle raw materials instead of disposing as
waste.
Tool, accessories and packaging should be sorted for
environment-friendly recycling.
The plastic components are labelled for categorized recycling.
These instructions are printed on recycled paper manufactured
without chlorine.
Summary of Contents for MPC-110
